Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC B2557: Passenger Compartment Lamp Control Circuit LowDTC B2558: Passenger Compartment Lamp Control Circuit High
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Courtesy Lamp B+ | B2557 | 1 | -- | -- |
PRK/LP Relay B+ | 1 | 1 | -- | -- |
Interior Lamp Switch Signal | 2 | 2 | -- | -- |
Park Lamp Switch Signal | 2 | 2 | 2 | -- |
Courtesy Lamp Control | 1 | 1 | B2558 | -- |
Park Lamp Relay Control | 1 | 1 | 1 | -- |
Park Lamp Control | 1 | 1 | 1 | -- |
Headlamp Switch Low Reference | -- | 2 | -- | -- |
Dome/Reading Lamp Ground | -- | 1 | 1 | -- |
Dome Lamp Ground | -- | 1 | 1 | -- |
Door Lock/Window Switch Ground -- Passenger | -- | 1 | -- | -- |
Door Lock/Window Switch Ground-- Driver | -- | 1 | -- | -- |
I/P Courtesy Lamp Ground -- Left | -- | 1 | 1 | -- |
I/P Courtesy Lamp Ground -- Right | -- | 1 | 1 | -- |
1. Courtesy Lamps Malfunction 2. Courtesy Lamps Switch Malfunction | ||||
Circuit/System Description
B+ is supplied to the courtesy lamps by the body control module (BCM) through an inadvertent power supply circuit. In the event that any of these lamps were to remain illuminated for a period of more than 20 minutes with the ignition switch in the OFF position, the BCM will deactivate the inadvertent power supply to prevent a total battery discharge condition. Courtesy lamp operation is controlled by the BCM through low side drive control circuits, and any time the inadvertent power supply is active the BCM turns on the courtesy lamps by grounding the control circuits.
Conditions for Running the DTC
Battery voltage must be between 9-16 volts.
Conditions for Setting the DTC
B2557
The courtesy lamp voltage reference circuit is shorted to ground.
B2558
The courtesy lamp control circuit is shorted to voltage.
Action Taken When the DTC Sets
The courtesy lamps will not operate or will remain always on.
Conditions for Clearing the DTC
| • | This DTC will clear on current status after the condition for setting the fault is corrected. |
| • | A history DTC will clear after 100 consecutive ignition cycles without a fault present. |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Interior Lighting Systems Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Ignition ON, command the courtesy lamps On and Off with a scan tool.
| ⇒ | If the courtesy lamps do not turn on or remain on at all times, perform the Courtesy Lamp Control Circuit Test. |
Circuit/System Testing
Courtesy Lamp Control Circuit Test
- Ignition OFF, disconnect the harness connector at the appropriate courtesy lamp.
- Ignition ON, verify that a test lamp illuminates between the listed courtesy lamp supply circuit terminal and ground.
- Connect a test lamp between the listed control circuit terminal and courtesy lamp supply circuit terminal.
- Operate the courtesy lamp switch ON and OFF. The test lamp should turn ON and OFF when changing between the commanded states.
- If all circuits test normal, test or replace the appropriate bulb.
| • | Dome/Reading Lamps terminal B |
| • | Dome Lamp terminal B |
| • | I/P Courtesy Lamp -- Left terminal A |
| • | I/P Courtesy Lamp -- Right terminal A |
| • | Vanity Mirror Lamp -- Left terminal A |
| • | Vanity Mirror Lamp -- Right terminal A |
| ⇒ | If the test lamp does not illuminate, test the courtesy lamp supply circuit for a short to ground or an open/high resistance. If the circuit tests normal, test or replace the BCM. |
| • | Dome/Reading Lamps terminal A and B |
| • | Dome Lamp terminal A and B |
| • | I/P Courtesy Lamp -- Left terminal B and A |
| • | I/P Courtesy Lamp -- Right terminal B and A |
| • | Vanity Mirror Lamp -- Left terminal B and A |
| • | Vanity Mirror Lamp -- Right terminal B and A |
| ⇒ | If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM. |
| ⇒ | If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for BCM replacement, programming, and setup |
