DTC P0563 ECM
Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC P0563: System Voltage High - ECMDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
B+ | P0562 | P0562 | -- | -- |
Ground | -- | P0562 | -- | -- |
Circuit/System Description
The engine control module (ECM) monitors the system voltage to ensure that the voltage stays within the proper range. Damage to components, and incorrect data may occur if the voltage is out of range. If the ECM detects that the system voltage is too high, then DTC P0563 sets.
Conditions for Running the DTC
The engine is running.
Conditions for Setting the DTC
The ECM detects that the system voltage is greater than 18 V for 5 seconds.
Action Taken When the DTC Sets
DTC P0563 is a type C DTC.
Conditions for Clearing the DTC
DTC P0563 is a type C DTC.
Diagnostic Aids
| • | DTC P0563 could be set by overcharging with a battery charger or jump starting. |
| • | A high voltage value in multiple modules indicates a concern in the charging system. |
Reference Information
Schematic Reference
| • | Engine Controls Schematics for the 3.7L (LLR) engine |
| • | Engine Controls Schematics for the 5.3L (LH8) engine |
Connector End View Reference
Description and Operation
Charging System Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
- Engine running, accessories OFF, measure and record the battery voltage at the battery terminals. The voltage should be between 12.6 and 15.0 V.
- If all circuits test normal, replace the ECM.
| ⇒ | If not within the specified range, refer to Charging System Test. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for ECM replacement, setup, and programming.
DTC P0563 FSCM
Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC P0563: System Voltage High - FPCMDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
B+ | P0562 | P0562 | -- | -- |
Ground | -- | P0562 | -- | -- |
Circuit/System Description
The fuel pump control module (FPCM) monitors the system voltage to ensure that the voltage stays within the proper range. Damage to components, and incorrect data may occur when the voltage is out of range. If the FPCM detects that the system voltage is high, DTC P0563 sets.
Conditions for Running the DTC
The ignition is ON.
Conditions for Setting the DTC
The FPCM detects that the system voltage is greater than 18 V.
Action Taken When the DTC Sets
DTC P0563 is a type C DTC.
Conditions for Clearing the DTC
DTC P0563 is a type C DTC.
Diagnostic Aids
| • | A high voltage DTC in multiple modules indicates a concern in the charging system. |
| • | This DTC could be set by overcharging with a battery charger or jump starting. |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Charging System Description and Operation
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
- Engine running, accessories OFF, measure and record the battery voltage at the battery terminals. The voltage should be between 12.6 and 15.0 V.
- If all circuits test normal, replace the FPCM.
| ⇒ | If not within the specified range, refer to Charging System Test. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for FPCM replacement, setup, and programming.
