GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Holden 🢒 2008 🢒 Barina 🢒 DTC 🢒 DTC B1483

Circuit Description

When the ignition switch is turned to ON, the sensing and diagnostic module (SDM) will perform a turn-on test to diagnose critical malfunctions within the SDM itself.

These test ignition and deployment loop voltages are measured to ensure that they are within their normal voltage ranges. The SDM monitors the voltages at the driver low and the passenger low to detect shorts to ground or voltage in the deployment loops.

If the resistance is in the 2-10 kilo ohms range, the defect may occur, depending on the SDM. The normal resistance is over 10 kilo ohms.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC B1483 Driver Frontal Deployment Loop Stage 2 Short to Ground

Conditions for Running the DTC

Ignition voltage is within the normal operating voltage range.

Conditions for Setting the DTC
    • The air bag wiring of the 2nd stage driver's high is shorted to ground.
    • The air bag wiring of the 2nd stage driver's low is shorted to ground.

Action Taken When the DTC Sets

The SDM commands the AIR BAG indicator ON.

Conditions for Clearing the DTC

The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used.

Step

Action

Values

Yes

No

Caution: Refer to Sensing and Diagnostic Module Handling Caution in the Preface section.

Caution: Refer to Sensing and Diagnostic Module Voltage after Ignition is Turned Off Caution in the Preface section.

Schematic Reference: SIR Schematics

Connector End View Reference: SIR Connector End Views

1

Did you perform a Diagnostic System Check - Vehicle?

 

Go to Step 2

Go to Diagnostic System Check - Vehicle

2
  1. Confirm the ignition switch is OFF and the sensing and diagnostic module (SDM) fuse has been removed.
  2. Wait for 1 minute to discharge the SDM charger.

Has the SDM discharged?

--

Go to Step 3

--

3

Visually inspect the connector and the wiring of the driver air bag.

Is the air bag wiring damaged?

--

Go to Step 7

Go to Step 4

4
  1. Confirm the ignition switch is OFF.
  2. Remove the steering wheel module.
  3. Disconnect the connector of the SDM wiring.
  4. Measure the resistance between the high, low wiring of the 2nd stage steering wheel module connector and ground.

Is the resistance equal to the specified value?

∞

Go to Step 5

Go to Step 6

5
  1. Replace the SDM. Refer to Inflatable Restraint Sensing and Diagnostic Module Replacement .
  2. Confirm the ignition switch is ON.
  3. Use the scan tool in order to clear the DTCs.
  4. Perform the Diagnostic System Check - Vehicle .

Is the DTC removed?

--

Go to Step 10

Go to Step 9

6
  1. Remove the connector from the steering wheel module coil wiring.
  2. Measure the resistance between the high, low wiring of the 2nd stage steering wheel module coil connector and ground.

Is the resistance at or above the specified value?

∞

Go to Step 8

Go to Step 7

7

Replace the air bag wiring.

Is the replacement complete?

--

Go to Step 10

--

8

Replace the steering wheel module coil. Refer to Inflatable Restraint Steering Wheel Module Coil Replacement .

Is the replacement complete?

--

Go to Step 10

--

9

Replace the steering wheel module. Refer to Inflatable Restraint Steering Wheel Module Replacement .

Is the replacement complete?

--

Go to Step 10

--

10
  1. Reconnect all SIR components.
  2. Verify that all components, connectors and connector position assurances (CPAs) are properly mounted.
  3. Use the scan tool in order to clear the DTCs.
  4. Operate the vehicle within the Conditions for Running the DTC, as specified in the supporting text.

Does the DTC reset?

 

Go to Step 2

System OK