For 1990-2009 cars only
Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC P2177: Fuel Trim System Lean at Cruise or Accel Bank 1DTC P2179: Fuel Trim System Lean at Cruise or Accel Bank 2
DTC P2187 : Fuel Trim System Lean at Idle Bank 1
DTC P2189: Fuel Trim System Lean at Idle Bank 2
Circuit Description
The engine control module (ECM) controls the air/fuel metering system in order to provide the best possible combination of driveability, fuel economy, and emission control. Fuel delivery is controlled differently during Open and Closed Loop. During Open Loop, the ECM determines fuel delivery based on sensor signals without heated oxygen sensor (HO2S) input. During Closed Loop, the HO2S inputs are added and used by the ECM to calculate short and long term fuel delivery adjustments. If the HO2S indicate a lean condition, fuel trim values will be above 0 percent. If the HO2S indicate a rich condition, fuel trim values will be below 0 percent. Short term fuel trim values change rapidly in response to the HO2S signals. Long term fuel trim makes coarse adjustments in order to maintain an air/fuel ratio of 14.7:1.
Conditions for Running the DTC
P2177 or P2179
| • | Before the ECM can report DTC P2177 or P2179, failed, DTCs P0008, P0009, P0010, P0011, P0013, P0014, P0016, P0017, P0018, P0019, P0020, P0021, P0023, P0024, P0101, P0121, P0122, P0123, P0133, P0153, P0201, P0202, P0203, P0204, P0205, P0206, P0221, P0222, P0223, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0335, P0336, P0338, P0443, P0458, P0459, P0461, P0462, P0463, P2068 P2088, P2089, P2090, P2091, P2092, P2093, P2094, and P2095 must run and pass. |
| • | The engine speed is between 1,200-3,400 RPM. |
| • | The mass air flow (MAF) is less than 83 grams/second. |
| • | The throttle angle is less than 100 percent. |
| • | The engine load is between 17-45 percent. |
| • | The fuel system is in closed loop. |
| • | The engine is not in decel fuel cut-off (DEFCO). |
| • | The long term fuel trim is active. |
| • | The engine coolant temperature (ECT) is warmer than 60°C (140°F). |
| • | The intake air temperature (IAT) is colder than 61°C (142°F). |
| • | The evaporative emission (EVAP) canister purge solenoid valve is not enabled. |
| • | The fuel level is greater than 12 percent. |
| • | The amount of air flow into the engine is greater than 7,000 grams. |
| • | DTC P2177 and P2179 run continuously once the above conditions are met for at least 300 seconds. |
P2187 or P2189
| • | Before the ECM can report DTC P2187 or P2189, failed, DTCs P0008, P0009, P0010, P0011, P0013, P0014, P0016, P0017, P0018, P0019, P0020, P0021, P0023, P0024, P0101, P0121, P0122, P0123, P0133, P0153, P0201, P0202, P0203, P0204, P0205, P0206, P0221, P0222, P0223, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0335, P0336, P0338, P0443, P0458, P0459, P0461, P0462, P0463, P2068 P2088, P2089, P2090, P2091, P2092, P2093, P2094, and P2095 must run and pass. |
| • | The engine speed is between 519-1,001 RPM. |
| • | The engine load is between 7-25 percent |
| • | The MAF is between 1-7 grams per second. |
| • | The fuel system is in closed loop. |
| • | The fuel system is in closed loop. |
| • | The engine is not in decel fuel cut-off (DEFCO). |
| • | The long term fuel trim is active. |
| • | The engine coolant temperature (ECT) is warmer than 60°C (140°F). |
| • | The intake air temperature (IAT) is colder than 61°C (142°F). |
| • | The evaporative emission (EVAP) canister purge solenoid valve is not enabled. |
| • | The fuel level is greater than 12 percent. |
| • | The amount of air flow into the engine is greater than 7,000 grams. |
| • | DTC P2187 and P2189 run continuously once the above conditions are met. |
Conditions for Setting the DTC
P2177 or P2179
The Total Fuel Trim Avg. is greater than 23 percent for greater than 4 seconds.
P2187 or P2189
The Total Fuel Trim Avg. is greater than 40 percent. The LT FT Idle/Decel is greater than 7 percent. The condition exists for 4 seconds.
Action Taken When the DTC Sets
DTCs P2177, P2179, P2187 and P2189 are Type B DTCs.
Conditions for Clearing the MIL/DTC
DTCs P2177, P2179, P2187 and P2189 are Type B DTCs.
Diagnostic Aids
| • | A fuel system delivery condition causes this DTC to set. Thoroughly inspect all items that cause a lean condition. Refer to Fuel System Diagnosis. |
| • | Any un-metered air into the engine causes this DTC to set. Thoroughly inspect all areas of the engine for vacuum leaks. |
| • | A MAF sensor condition can cause this DTC without setting a MAF DTC. If there is a MAF sensor condition, the MAF sensor parameters will appear to be within range. |
| • | Inspect the PCV system for improper operation. Inspect the air filter for being the correct one for this application. Make sure that the engine oil fill cap is in place and that it is tight. Verify that the engine oil dip stick is fully seated. |
Reference Information
Schematic Reference
Connector End View Reference
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
- Ignition ON, observe the scan tool DTC information. Verify that there are no other DTCs set.
- Observe the scan tool barometric pressure (BARO) sensor pressure parameter and compare the reading on the scan tool to the barometric pressure table. Refer to Altitude Versus Barometric Pressure.
- Engine idling at normal operating temperature, observe the scan tool Total Fuel Trim Avg. parameter. The Total Fuel Trim Avg. should be between -22 to +23 percent.
- Operate the vehicle within the conditions for running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that are captured in the Freeze Frame/Failure Records Data List.
| ⇒ | If there are other DTCs set besides DTC P2177, P2179, P2187, or P2189, refer to Diagnostic Trouble Code (DTC) List - Vehicle for further diagnosis. |
| ⇒ | If the BARO sensor pressure is not within the range specified for your altitude, refer to DTC P2227, P2228, or P2229. |
Circuit/System Testing
- Observe the scan tool LT FT Bn 1 and Bn 2 Cruise/Accel parameters, in order to determine whether the lean condition is effecting only one bank of the engine, or is common to both banks of the engine.
- If all conditions test normal, refer to Diagnostic Aids.
| ⇒ | If the lean condition is common to both banks, inspect for the following conditions: |
| • | A mass air flow (MAF) sensor signal that is skewed--If the Short Term FT parameters for both banks changes greater than 20 percent when the MAF sensor is disconnected, refer to DTC P0101. |
| • | The air intake system after the MAF sensor for vacuum leaks |
| • | Fuel contamination--Refer to Alcohol/Contaminants-in-Fuel Diagnosis. |
| • | Splits, kinks, or improper connections at the vacuum hoses |
| • | The fuel system is operating lean--Refer to Fuel System Diagnosis. |
| • | Vacuum leaks at the intake manifold or throttle body |
| • | Leaking crankcase ventilation system |
| • | The engine control module grounds for being clean, tight, and in the correct locations |
| • | A high engine oil level condition--A high engine oil level causes oil residue to form on the mass air flow (MAF) sensor, causing a lean indication. The MAF sensor does not need to be replaced. |
| ⇒ | If the lean condition is common to only one bank of the engine, inspect for the following conditions: |
| • | Vacuum leaks that only affect one bank of the engine--For example, the intake manifold, the injector O-rings. |
| • | Lean injectors--Refer to Fuel Injector Solenoid Coil Test. |
| • | Missing, restricted, or leaking exhaust components--Refer to Symptoms - Engine Exhaust. |
| • | The heated oxygen sensor (HO2S) is installed securely and the electrical connector is not contacting the exhaust system. |
| • | An engine mechanical condition--Refer to Symptoms - Engine Mechanical. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
