Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provide an overview of each diagnostic category. |
DTC Descriptors
DTC P2300: Ignition Coil 1 Control Circuit Low VoltageDTC P2301: Ignition Coil 1 Control Circuit High Voltage
DTC P2303: Ignition Coil 2 Control Circuit Low Voltage
DTC P2304: Ignition Coil 2 Control Circuit High Voltage
DTC P2306: Ignition Coil 3 Control Circuit Low Voltage
DTC P2307: Ignition Coil 3 Control Circuit High Voltage
DTC P2309: Ignition Coil 4 Control Circuit Low Voltage
DTC P2310: Ignition Coil 4 Control Circuit High Voltage
DTC P2312: Ignition Coil 5 Control Circuit Low Voltage
DTC P2313: Ignition Coil 5 Control Circuit High Voltage
DTC P2315: Ignition Coil 6 Control Circuit Low Voltage
DTC P2316: Ignition Coil 6 Control Circuit High Voltage
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Ignition 1 Voltage | 1 | 2 | -- | -- |
Ignition Coil 1 Control Circuit | P0301, P2300 | P0301, P2300 | P0301, P2301 | -- |
Ignition Coil 2 Control Circuit | P0302, P2303 | P0302, P2303 | P0302, P2304 | -- |
Ignition Coil 3 Control Circuit | P0303, P2306 | P0303, P2306 | P0303, P2307 | -- |
Ignition Coil 4 Control Circuit | P0304, P2309 | P0304, P2309 | P0304, P2310 | -- |
Ignition Coil 5 Control Circuit | P0305, P2312 | P0305, P2312 | P0305, P2313 | -- |
Ignition Coil 6 Control Circuit | P0306, P2315 | P0306, P2315 | P0306, P2316 | -- |
Ground Circuit | -- | -- | -- | -- |
| ||||
Circuit/System Description
Ignition 1 voltage is supplied to the ignition coils . The engine control module (ECM) provides a ground for the ignition coil (IC) control circuits. When the ECM removes the ground path of the ignition primary coil, the magnetic field produced by the coil collapses. The collapsing magnetic field produces a voltage in the secondary coil which ignites the spark plugs. The sequencing and timing are controlled by the ECM.
Conditions for Running the DTC
| • | DTCs P0016 and P0340 are not set. |
| • | The engine speed is more than 512 RPM. |
| • | The engine coolant temperature (ECT) is greater than 21°C (69°F). |
| • | The ignition 1 voltage is between 10-16 volts. |
| • | The DTCs run continuously once the above condition is met. |
Conditions for Setting the DTC
The ECM detects an open, short to ground, or a short to voltage on the IC circuit.
Action Taken When the DTC Sets
DTCs P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310, P2312, P2313, P2315, and P2316 are Type A DTCs.
Conditions for Clearing the DTC
DTCs P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310, P2312, P2313, P2315, and P2316 are Type A DTCs.
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation:
Electronic Ignition (EI) System Description
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Circuit/System Verification
- Engine idling, observe the scan tool DTC information parameter. DTCs P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310, P2312, P2313, P2315, and P2316 should not set.
- If the vehicle passes the Circuit/System Verification test, then operate the vehicle within the conditions for running the DTC. You may also operate the vehicle within the conditions that are captured in the Freeze Frame/Failure Records Data List.
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the appropriate ignition coil.
- Test for less than 5 ohms of resistance between the ground circuit and ground.
- Ignition ON, command the fuel pump relay ON with a scan tool. Test for B+ between the ignition 1 voltage circuit and ground.
- Engine idling, verify the frequency is more than 10 Hz between the appropriate ignition control circuit and ground.
- If all circuits test normal, test or replace the ignition coil.
| ⇒ | If greater than the specified range, test the ground circuit of the ignition coil for an open/high resistance. |
| ⇒ | If less than B+, test the ignition 1 voltage circuit for a short to ground or an open/high resistance. If the circuit tests normal and the ignition 1 voltage circuit fuse is open, test all components connected to the ignition 1 voltage circuit and replace as necessary. |
Important: Set the DMM to the AC Hertz scale for this test.
| ⇒ | If less than the specified range, test the ignition control circuit for a short to voltage, short to ground or an open/high resistance. If the circuit tests normal, replace the ECM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for engine control module replacement, setup, and programming |
