GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Holden 🢒 2008 🢒 Epica 🢒 Body Systems 🢒 Fixed and Moveable Windows 🢒 DTC P0667, P0668, or P0669

Diagnostic Instructions
    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC P0667:  Transmission Control Module (TCM) Temperature Sensor Performance

DTC P0668:  Transmission Control Module (TCM) Temperature Sensor Circuit Low Voltage

DTC P0669:  Transmission Control Module (TCM) Temperature Sensor Circuit High Voltage

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

TCM Temperature Sensor

P0668

P0669

--

P0667

Circuit/System Description

The transmission control module (TCM) temperature sensor is located inside of the control solenoid (w/body and TCM) valve assembly. The control solenoid (w/body and TCM) valve assembly has no seviceable parts. The TCM temperature sensor measures the temperature of the TCM. This temperature reading is used in various shifting and diagnostic routines in the TCM software. This fault is handled inside the TCM and no external circuits are involved.

Conditions for Running the DTC

P0667

    • No TFT DTCs P0711, P0712, or P0713.
    • No ISS DTCs P0716 or P0717.
    • No OSS DTCs P0722 or P0723.
    • The ignition voltage is between 9.0 volts and 19.0 volts.
    • The engine speed is greater than 500 RPM for 5 seconds or more.
    • DTC P0667 has not passed this key ON.
    • The TCM temperature is between -40 and +150°C (-40 and +302°F).

P0668

    • The ignition voltage is between 9.0 volts and 19.0 volts.
    • The engine speed is greater than 500 RPM for 5 seconds or more.
    • DTC P0668 has not failed this ignition cycle.

P0669

    • No ISS DTCs P0716 or P0717.
    • No OSS DTCs P0722 or P0723.
    • The ignition voltage is between 9.0 volts and 19.0 volts.
    • The engine speed is greater than 500 RPM for 5 seconds or more.
    • DTC P0669 has not failed this ignition cycle.
    • The transmission output shaft speed is 200 RPM or greater for 200 seconds or more.
    • The TCC slip speed is 120 RPM or greater for 200 seconds or more.

Conditions for Setting the DTC

P0667 - Fail Case 1

    • Vehicle speed is 8 km/h (5 mph) or greater for 300 seconds cumulative.
    • Torque converter clutch (TCC) slip speed is greater than 150 RPM for 300 seconds cumulative.
    • The TCM temperature is between -40 and +76°C (-40 and +169°F).
    • The transmission fluid temperature (TFT) is 70°C (158°F) or greater.
    • The TCM temperature has changed by less than 2.0°C (3.6°F) in 300 seconds.
    • The TFT has increased by 55°C (99°F) since startup.

P0667 - Fail Case 2

    • Vehicle speed is 8 km/h (5 mph) or greater for 300 seconds cumulative.
    • TCC slip speed is greater than 150 RPM for 300 seconds cumulative.
    • The TCM temperature is between 76-150°C (168-302°F).
    • The TCM temperature has changed by less than 2.0°C (3.6°F) in 300 seconds.
    • The TFT is 70°C (158°F) or greater.
    • The TFT has increased by 55°C (99°F) since startup.

P0667 - Fail Case 3

The TCM temperature changes by 20°C (36°F) or greater 5 times over 7 seconds.

P0668

The TCM temperature is 254°C (489°F) or greater for 12.75 seconds or more.

P0669

The TCM temperature is -254°C (-425°F) or less for 12.75 seconds or more.

Action Taken When the DTC Sets
    • DTCs P0667, P0668, and P0669 are Type C DTCs.
    • The TCM allows the vehicle to operate in transmission protection mode.

Conditions for Clearing the DTC

DTCs P0667, P0668, and P0669 are Type C DTCs.

Diagnostic Aids

Reprogram the TCM and retest for the DTC to see if the DTC resets.

Reference Information

Description and Operation

    •  Transmission General Description
    •  Transmission Component and System Description
    •  Electronic Component Description

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification
  1. Engine ON, verify the scan tool TCM Temperature parameter is between -254 and +254°C (-425 and +489°F).
    2. ⇒If not within the specified range, replace the control solenoid (w/body and TCM) valve assembly.
  2. Operate the vehicle at 64 km/h (40 mph) for at least 300 seconds while observing the TCM power up temperature sensor and the TCM temperature sensor. Verify that the transmission fluid temperature is within 10°C (18°F) of the TCM temperature sensor.
    3. ⇒If not within the specified range, replace the control solenoid (w/body and TCM) valve assembly.
  3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

       Important: Before replacing the TCM, perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection .

    • Refer to Control Module References for control solenoid (w/body and TCM) valve assembly replacement, setup, and programming.
    • Perform the Service Fast Learn Adapts following all transmission related repairs.