Special Tools

1. Remove the fuel pump fuse.
2. Start the engine and repeat cranking until the remaining fuel in the fuel line is all consumed.

Warning: Refer to Battery Disconnect Warning in the Preface section.

3. Disconnect the negative battery cable.
4. Drain the engine coolant. Refer to Cooling System Draining and Filling.
5. Drain the engine oil.



6. Drain the transaxle oil.
7. Drain the power steering oil.
8. Recover the refrigerant. Refer to Refrigerant Recovery and Recharging.
9. Remove the engine beautification cover.
10. Remove the air filter snorkel.
11. Remove the air filter housing assembly.



12. Remove the breather hose.
13. Disconnect the throttle cable from the throttle body assembly.



14. Disconnect the coolant reservoir hoses.
15. Remove the coolant reservoir. Refer to Radiator Surge Tank Replacement.



16. Disconnect the power steering pump outlet pipe.
17. Disconnect the fuel rail hose and fuel feeding/return pipe.



18. Disconnect the connectors on the following:

•	The oxygen sensor (O2S)

•	The exhaust gas recirculation (EGR)

•	The charcoal canister purge solenoid valve

•	The MAP sensor

•	The throttle body

•	The engine oil pressure sensor

•	The camshaft position (CMP) sensor

•	The knock sensor

•	The variable intake system (VIS)

•	The engine coolant temperature sensor




19. Detach the wiring harness from the wiring harness bracket on the cylinder block.



20. Disconnect the engine block ground by removing the engine block ground bolts.



21. Remove the battery.



22. Disconnect the automatic transaxle cable.
23. Disconnect the inhibit switch connector.
24. Disconnect the connectors on the transaxle.
25. Disconnect the alternator connector and wiring harness.



26. Remove the upper and lower radiator hoses.
27. Remove the front wheels.
28. Remove the engine under covers.



29. Remove the front axle shaft. Refer to Wheel Drive Shaft Replacement.
30. Remove the front muffler. Refer to Exhaust Muffler Replacement.




Caution: When raising or supporting the engine for any reason, do not use a jack under the oil pan, any sheet metal, or crankshaft balancer. Jacking against the oil pan may cause it to crack or break.

31. Support the engine assembly using the J 28467-B (1).



32. Remove the front engine mount bracket-to-damper bush bolt/nut and the rear transaxle mount-to-damper bush bolt/nut.



33. Remove the center front suspension member bolts and the center front suspension member.



34. Disconnect the connector on the compressor.
35. Disconnect the refrigerant suction and discharge pipe block from the compressor.



36. Remove the oil filter.



37. Support the engine and transaxle with the J 39580 (1).



38. Remove the right engine mount bracket. Refer to Engine Mount Replacement.



39. Remove the left engine mount bracket. Refer to Engine Mount Replacement.
40. Separate the engine and transaxle assembly from the engine compartment.



41. Remove the starter. Refer to Starter Motor Replacement.



42. Remove the 3 transaxle torque converter bolts.



43. Remove the transaxle-to-engine block bolts.



44. Remove the engine block-to-transaxle bolts.



45. Remove the engine block-to-transaxle bolts.

Caution: Carefully inspect the transmission and the surrounding areas to be sure no lines, hoses or wires will interfere with the transmission removal. In order to avoid damage to the transmission or the torque converter, support the transmission with a dolly jack. Do not let the torque converter fall.

46. Remove the engine assembly from the transaxle.



47. Remove the rear transaxle mount bracket.
48. Remove the front damper bush bracket.

Caution: Carefully inspect the transmission and the surrounding area to be sure no lines, hoses or wires will interfere with the transmission installation. When raising and moving the transmission, do not let the torque converter slip off the shaft. The transmission or torque converter can be damaged.

1. Install the engine assembly to the transaxle.

Caution: Refer to Fastener Caution in the Preface section.

2. Install the engine block-to-transaxle bolts near the rear transaxle bracket. Tighten the engine block-to-transaxle bolts to 72 N·m (53 lb ft)



3. Install the engine block-to-transaxle bolts near the front engine mount bracket and tighten to 72 N·m (53 lb ft).



4. Install the transaxle-to-engine block bolts near the rear support bracket and tighten the bolts to 72 N·m (53 lb ft).



5. Tighten the 3 flexible plate-to-torque converter retaining bolts and tighten to 45 N·m (33 lb ft).



6. Install the rear transaxle mount bracket and tighten the bolts to 65 N·m (48 lb ft).



7. Install the front damper bush bracket and tighten the bracket bolts to 65 N·m (48 lb ft).



8. Install the starter. Refer to Starter Motor Replacement.
9. Install the engine and transaxle assembly using the J 39580  (1).



10. Install the left engine mount bracket. Refer to Engine Mount Replacement.



11. Install the right engine mount bracket. Refer to Engine Mount Replacement.



12. Support the engine and transaxle assembly using the J 28467-B  (1).
13. Remove the J 39580 .



14. Install the oil filter and tighten to 14 N·m (124 lb in).
15. Connect the connector on the compressor.
16. Connect the refrigerant suction and discharge pipe block to the compressor. Refer to Discharge Hose Replacement.



17. Install the center front suspension member and tighten the member bolts to 90 N·m (66 lb ft).



18. Install the front engine mount bracket-to-damper bush bolt/nut and the rear transaxle mount bracket-to-damper bush bolt/nut.

•	Tighten the front engine mount bracket-to-damper bush bolt/nut to 80 N·m (52-66 lb ft).

•	Tighten the rear transaxle mount bracket-to-damper bush bolt/nut to 80 N·m (52-66 lb ft).

19. Remove the J 28467-B .



20. Install the front muffler. Refer to Exhaust Muffler Replacement.



21. Install the axle shaft. Refer to Wheel Drive Shaft Replacement.
22. Install the engine under cover and tighten the bolts to 23 N·m (17 lb ft).
23. Install the front wheels.
24. Install the upper and lower radiator hoses.



25. Connect the alternator connector and wiring harness.
26. Connect the connectors on the transaxle.
27. Connect the inhibit switch connector.
28. Connect the automatic transmission cable.



29. Install the battery.



30. Connect the engine block grounds.



31. Attach the wiring harness to the wiring harness bracket on the cylinder block.
32. Connect all the engine control wiring connectors.
33. Connect the fuel rail hose and fuel feeding/return pipe.
34. Connect the power steering pump outlet pipe.



35. Install the coolant reservoir. Refer to Radiator Surge Tank Replacement. Tighten the coolant reservoir bolts to 4 N·m (35 lb in).



36. Connect the throttle cable to the throttle body.
37. Install the air filter housing and breather hose and tighten the bolt to 10 N·m (89 lb in).



38. Install the air filter snorkel and tighten the bolt to 6 N·m (53 lb in).



39. Install the engine beautification cover and tighten the bolts to 10 N·m (89 lb in).
40. Connect the connectors and hoses.
41. Recharge the refrigerant. Refer to Refrigerant Recovery and Recharging.
42. Fill and bleed the power steering system. Refer to Power Steering System Bleeding.
43. Fill the transaxle oil
44. Fill the engine oil.
45. Refill the engine coolant system. Refer to Cooling System Draining and Filling.
46. Install the fuel pump fuse.
47. Connect the negative battery cable.