GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Holden 🢒 2008 🢒 Lumina Ute 🢒 Diagnostic Navigation 🢒 Vehicle Diagnostic Information 🢒 Electronic Brake Control Module Replacement

Removal Procedure

    Caution: Refer to Brake Fluid Caution in the Preface section.

    Caution: Refer to Brake Fluid Irritant Caution in the Preface section.

    Notice: Refer to Adding Fluid to the Brake System Notice in the Preface section.

    Notice: Refer to Brake Fluid Effects on Paint and Electrical Components Notice in the Preface section.

    Important: If the electronic brake control module (EBCM) or brake pressure modulator valve (BPMV) is to replaced under manufacturer's warranty, do not disassemble the EBCM/BPMV assembly. If the EBCM or BPMV is faulty, replace the EBCM/BPMV as an assembly.

    Important: The area around the EBCM must be free from loose dirt to prevent contamination of disassembled ABS components.

  1. Ignition OFF.

    2. Object Number: 1943643 Size: SH
  2. Remove the EBCM/BPMV assembly. Refer to Brake Pressure Modulator Valve Assembly Replacement .
  3. Clean the EBCM/BPMV assembly.
  4. Rotate the EBCM connector tab (2) up to the unlocked position.

    5. Notice: To prevent equipment damage, never connect or disconnect the wiring harness connection from the EBCM with the ignition switch in the ON position.

  5. Disconnect the EBCM electrical connector (1) and position out of the way.

    6. Object Number: 1943646 Size: SH

    Important: EBCM to BPMV retaining screws are a single use only component. NEW EBCM to BPMV retaining screws must be installed whenever the EBCM to BPMV retaining screws are removed.

  6. Remove the EBCM to BPMV retaining screws (1).

    7. Discard the screws.

  7. Clean the surface of the EBCM/BPMV assembly.

    8. Object Number: 1943634 Size: SH

    Important: The EBCM (1) cannot be repaired. If faulty, the EBCM (1) must be replaced.

  8. Separate the EBCM (1) from the BPMV (2).

Installation Procedure

    Caution: Refer to Brake Fluid Caution in the Preface section.

    Caution: Refer to Brake Fluid Irritant Caution in the Preface section.

    Notice: Refer to Adding Fluid to the Brake System Notice in the Preface section.

    Notice: Refer to Brake Fluid Effects on Paint and Electrical Components Notice in the Preface section.


    Object Number: 1943634 Size: SH

    Important: The seal is not available as a spare part and the mating surfaces cannot be mechanically reworked. If the seal or mating surfaces are damaged the EBCM/BPMV assembly must be replaced.

  1. Inspect the EBCM (1) to BPMV (2) mating surfaces and seal.
  2. Clean the seal surface of the BPMV.

    3. Important: Make sure the coils for the solenoid valves are aligned correctly. If they are not correctly aligned the EBCM (1) must be replaced.

    Important: Make sure the contact pins of the hydraulic pump are aligned correctly.

  3. Install the EBCM (1) to the BPMV (2).

    4. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 2017917 Size: SH
  4. Install the NEW EBCM to BPMV retaining screws.

    5. Tighten
    Tighten the EBCM to BPMV screws in sequence to 8 Nm (71 lb in).


    Object Number: 1943643 Size: SH

    Notice: To prevent equipment damage, never connect or disconnect the wiring harness connection from the EBCM with the ignition switch in the ON position.

  5. Connect the EBCM electrical connector (1) to the EBCM (3).
  6. Rotate the EBCM connector tab (2) to the locked position.
  7. Use the scan tool in order to clear any DTCs.
  8. Perform the Auto Bleed Procedure. Refer to Antilock Brake System Automated Bleed Procedure .
  9. If installing a new EBCM it is necessary to program the EBCM. Refer to Service Programming System (SPS) .
  10. Perform the System Check - Vehicle. Refer to Diagnostic System Check - Vehicle .
  11. Calibrate the brake pedal position sensor. Refer to Service Programming System (SPS) .