Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category |
DTC Descriptors
DTC P0532: Air Conditioning A/C Refrigerant Pressure Sensor Circuit Low VoltageDTC P0533: Air Conditioning A/C Refrigerant Pressure Sensor Circuit High Voltage
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
5-Volt Reference | P0532 | P0532 | P0533 | -- |
A/C Refrigerant Pressure Sensor Signal | P0532 | P0533 | P0533 | -- |
Low Reference | -- | P0532 | P0533 | -- |
Circuit/System Description
The engine control module (ECM) monitors the high side refrigerant pressure through the A/C refrigerant pressure sensor. The ECM supplies a 5-volt reference and a low reference to the sensor. Changes in the A/C refrigerant pressure cause the sensor signal to the ECM to vary. When the pressure is high, the signal voltage is high. When the pressure is low, the signal voltage is low. When pressure is high, the ECM commands the cooling fans on. When pressure is too high or too low, the ECM will not allow the A/C compressor clutch to engage.
Conditions for Running the DTC
| • | Engine is running. |
| • | Any of the conditions for setting the DTC are met for 15 seconds. |
| • | Battery voltage is between 11-18 volts. |
Conditions for Setting the DTC
| • | The ECM detects that the A/C pressure is less than 1 psi (0.01 volt). |
| • | The ECM detects that the A/C pressure is more than 428 psi (4.92 volts). |
Action Taken when the DTC Sets
DTCs P0532 or P0533 are type B DTCs.
Conditions for Clearing the MIL/DTC
DTCs P0532 or P0533 are type B DTCs.
Diagnostic Aids
A malfunction within the refrigerant system causing high pressure can cause this DTC to set.
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Electrical Information Reference
Scan Tool Reference
Circuit/System Verification
Ignition ON, observe the scan tool A/C High Side Pressure Sensor parameter. The reading should be between 1 psi and 428 psi.
Circuit/System Testing
- Ignition OFF, disconnect the A/C pressure sensor harness connector.
- Ignition OFF, test for less than 1 ohm of resistance between the low reference circuit terminal and ground.
- Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal and ground.
- Verify the scan tool A/C High Side Pressure Sensor parameter is less than 428 psi.
- Install a 3-A fusible link wire between the signal circuit terminal 3 and the 5-volt reference circuit terminal 2. Verify the scan tool A/C High Side Pressure Sensor parameter is greater than 428 psi.
- If all circuits test normal, test or replace the A/C Pressure Sensor.
| ⇒ | If greater than 1 ohm, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM. |
| ⇒ | If less than 4.8 volts, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM. |
| ⇒ | If greater than 5.2 volts, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ECM. |
| ⇒ | If greater than 428 psi, test the signal circuit terminal for a short to voltage. If the circuit tests normal, replace the ECM. |
| ⇒ | If less than 428 psi, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the ECM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
