Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC C0297 00: Brake Applied Output CircuitDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
BCM B+ Terminal 4 X4 | B3445 00 | B3445 00 | -- | -- |
Brake Pedal Position Sensor 5-Volt Reference | C0277 06, C0890 03, C0161 71 | C0277 06, C0161 71 | C0277 07, C0161 71 | -- |
Brake Applied Signal Terminal 6 X5 | C0297 00, P0571 00 | 3 | 3 | -- |
Brake Pedal Position Sensor Signal | C0277 06, C0161 71 | C0277 06, C0161 71 | C0277 07, C0161 71 | C0277 09 |
Stop Lamp Control | B3445 00 | 1 | 1 | -- |
Brake Position Sensor Low Reference | -- | 1 | 1 | -- |
Center High Mounted Stop Lamp (CHMSL) Ground | -- | 2 | -- | -- |
Left Rear Tail/Stop Lamp Ground | -- | 1 | -- | -- |
Right Rear Tail/Stop Lamp Ground | -- | 1 | -- | -- |
1. Stop Lamps Malfunction 2. Center High Mounted Stop Lamp (CHMSL) Malfunction 3. Cruise Control Malfunction | ||||
Circuit/System Description
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The brake pedal position sensor provides an analog voltage signal that will increase as the brake pedal is applied. The body control module (BCM) provides a low reference signal and a 5-volt reference voltage to the brake pedal position sensor. When the variable signal reaches a voltage threshold indicating the brakes have been applied, the BCM will apply battery voltage to the stop lamp control circuit illuminating the left and right stop lamps and the center high mounted stop lamp (CHMSL). The BCM also applies battery voltage to the transmission control module (TCM) and engine control module (ECM) via the brake applied signal circuit.
Conditions for Running the DTC
| • | Battery voltage must be between 9-16 volts. |
| • | Brakes APPLIED. |
Conditions for Setting the DTC
The BCM detects a short to ground in the brake applied signal circuit.
Actions Taken When the DTC Sets
The Service Vehicle Soon indicator is commanded ON.
Conditions for Clearing the DTC
| • | The condition responsible for setting the DTC no longer exists. |
| • | A history DTC will clear once 100 malfunction-free ignition cycles have occurred. |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Exterior Lighting Systems Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing
- Ignition OFF, disconnect the appropriate harness connector listed below.
- Connect a test lamp between the appropriate signal circuit terminal listed below and ground.
- Ignition ON, command the stop lamps ON and OFF by applying and releasing the brake pedal. The test lamp should turn ON and OFF when changing between the commanded states.
- Ignition OFF, connect a test lamp between the appropriate signal circuit terminal listed below at the ECM harness connector and the connector terminal at the ECM.
- Ignition ON, command the stop lamps ON and OFF by applying and releasing the brake pedal. The test lamp should turn ON and OFF when changing between the commanded states.
- Ignition OFF, connect the harness connector at the ECM.
- Disconnect the harness connector at the TCM.
- Connect a test lamp between the appropriate signal circuit terminal listed below and ground.
- Ignition ON, command the stop lamps ON and OFF by applying and releasing the brake pedal. The test lamp should turn ON and OFF when changing between the commanded states.
- If all circuits test normal, replace the TCM.
| • | ECM X1 - with 6.0L |
| • | ECM X2 - with - 3.6L |
| • | ECM terminal 9 X1 - with 6.0L |
| • | ECM terminal 52 X2 - with 3.6L |
| ⇒ | If the test lamp is always ON, test the signal circuit for a short to voltage. If the circuit tests normal, replace the BCM. |
| ⇒ | If the test lamp is always OFF, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM. |
| • | ECM terminal 9 X1 - with 6.0L |
| • | ECM terminal 52 X2 - with 3.6L |
| ⇒ | If the test lamp does not turn ON and OFF when commanded, replace the ECM. |
| • | TCM terminal 42 - with 4L60E/4L65E |
| • | TCM terminal 38 - with 5L40E |
| • | TCM terminal 6 - 6L50E |
| ⇒ | If the test lamp is always ON, test the signal circuit for a short to voltage. If the circuit tests normal, replace the BCM. |
| ⇒ | If the test lamp is always OFF, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for BCM, ECM, or TCM replacement, setup, and programming |
