• | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
• | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
• | Diagnostic Procedure Instructions provides an overview of each diagnostic category |
The 1-2 shift solenoid valve is located in the control valve body of the transmission. The transmission control module (TCM) selects the required gear by turning the appropriate solenoid ON or OFF, enabling the transmission to shift. Refer to Shift Solenoid Valve State and Gear Ratio .
The TCM provides voltage to the solenoid through High Side Driver 2 (HSD2). The TCM uses a second driver to control the solenoid ground circuit. The controlled ground driver reports feedback voltage to the TCM. When the TCM commands the 1-2 shift solenoid valve ON, the voltage of the control circuit should be approximately 0 volts. When the TCM commands the 1-2 shift solenoid valve OFF, the voltage of the control circuit should be approximately system voltage.
When the TCM detects a continuous open or short to ground in the 1-2 shift solenoid valve circuit, then DTC P0973 sets. DTC P0973 is a type B DTC.
This diagnostic procedure supports the following DTC:
DTC P0973 1-2 Shift Solenoid (SS) Control Circuit Low Voltage
• | The engine run time is greater than 5 seconds. |
• | HSD2 is commanded ON. |
DTC P0973 sets when either of the following conditions occurs:
• | The TCM detects an open in the 1-2 shift solenoid valve circuit when HSD2 is commanded ON. |
• | The TCM detects a short to ground in the 1-2 shift solenoid valve circuit when HSD2 is commanded OFF. |
• | Powertrain braking is disabled at the time that the TCM first detects the failure, before the DTC sets. |
• | The TCM requests the ECM to illuminate the malfunction indicator lamp (MIL) during the second consecutive drive trip in which the Conditions for Setting the DTC are met. |
• | The TCM turns off power to all solenoids. When the solenoids are off: |
- | The transmission will operate in fifth gear if the vehicle has successfully completed a 1-2 upshift in the current ignition cycle. If the vehicle has not completed a 1-2 upshift in the current ignition cycle, the transmission will operate in fourth gear. If the transmission is operating in fifth gear, fourth gear may be obtained if the engine is stopped briefly and started again. |
- | The line pressure is at maximum. |
• | The TCM freezes transmission adaptive functions. |
• | Torque management is inhibited. |
• | At the time of the first failure, the TCM records the operating conditions when the Conditions for Setting the DTC are met. The TCM stores this information as a Failure Record. |
• | At the time of the second failure, the ECM records the operating conditions when the Conditions for Setting the DTC are met. The ECM stores this information as a Freeze Frame. |
• | The TCM stores DTC P0973 in TCM history. |
• | The ECM turns OFF the MIL after the sixth consecutive drive trip in which the TCM does not send a MIL illumination request. |
• | A scan tool can clear the MIL/DTC. |
• | The TCM clears the DTC from TCM history if the vehicle completes 40 warm-up cycles without an emission related diagnostic fault occurring. |
• | The TCM cancels the default actions when the ignition is OFF long enough in order to power down the TCM. |
The number below refers to the step number on the diagnostic table.
Listen for an audible click when the solenoid energizes.
Step | Action | Value(s) | Yes | No | ||||
---|---|---|---|---|---|---|---|---|
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |||||
2 |
Important: Before clearing the DTC, use the scan tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from both the ECM and the TCM. Is DTC P0976, P0979 or P2764 also set? | -- | Go to Step 3 | Go to Step 5 | ||||
3 | Test the ignition 1 voltage circuit of the 1-2 SS valve for an open or a short to ground between the TCM connector and the Automatic transmission inline 20-way connector. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 19 | Go to Step 4 | ||||
4 |
Important: The condition that affects this circuit may exist in other connecting branches of the circuit. Refer to Power Distribution Schematics for complete circuit distribution. Test the ignition 1 voltage circuit of the 1-2 SS valve for an open or a short to ground between the Automatic transmission inline 20-way connector and the 1-2 SS valve. Refer to Circuit Testing . Did you find the condition? | -- | Go to Step 16 | -- | ||||
5 |
Does the solenoid click when commanded ON and OFF? | -- | Go to Testing for Intermittent Conditions and Poor Connections | Go to Step 6 | ||||
6 |
Is the test lamp ON when you command the solenoid ON, and OFF when you command the solenoid OFF? | -- | Go to Step 10 | Go to Step 7 | ||||
7 | Is the test lamp always ON? | -- | Go to Step 8 | Go to Step 9 | ||||
8 | Test the control circuit of the 1-2 SS valve for a short to ground between the TCM connector and the Automatic transmission inline 20-way connector. Refer to Testing for Short to Ground and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 19 | Go to Step 18 | ||||
9 | Test the control circuit of the 1-2 SS valve for an open between the TCM connector and the Automatic transmission inline 20-way connector. Refer to Testing for Continuity and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 19 | Go to Step 18 | ||||
10 |
Is the resistance within the specified range? | 19-31 Ω | Go to Step 13 | Go to Step 11 | ||||
11 | Is the resistance greater than the specified value? | 31 Ω | Go to Step 12 | Go to Step 13 | ||||
12 |
Refer to Testing for Continuity . Did you find a condition? | -- | Go to Step 16 | Go to Step 17 | ||||
13 | Measure the resistance from the 1-2 SS valve control circuits of the J 45681 to ground. Refer to Component Connector End Views . Is the resistance less than the specified value? | 100 Ω | Go to Step 14 | Go to Step 15 | ||||
14 | Test the control circuit of the 1-2 SS valve for a short to ground between the Automatic transmission inline 20-way connector and the 1-2 SS valve. Refer to Testing for Short to Ground . Did you find the condition? | -- | Go to Step 16 | -- | ||||
15 | Measure the resistance between the 1-2 SS valve control circuits and all other terminals, except the 2-3 SS valve control circuit, the TCC PWM solenoid valve control circuit, and the ignition 1 voltage circuit of the J 45681 . Refer to Component Connector End Views . Is the resistance less than the specified value? | 100 Ω | Go to Step 16 | Go to Step 17 | ||||
16 | Replace the automatic transmission wiring harness. Refer to Transmission Internal Electrical Harness Replacement . Did you complete the replacement? | -- | Go to Step 19 | -- | ||||
17 | Replace the 1-2 SS valve. Refer to 1-2 Shift Solenoid Valve Replacement . Did you complete the replacement? | -- | Go to Step 19 | -- | ||||
18 | Replace the TCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 19 | -- | ||||
19 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | -- | Go to Step 20 | Go to Step 2 | ||||
20 | With the scan tool, observe the stored information, capture info and DTC info. Does the scan tool display any DTCs that you have not diagnosed? | -- | System OK |