Circuit Description
The powertrain control module (PCM) uses the cooling fan speed signal in order to determine the actual fan speed in relation to the desired fan speed. The PCM uses the cooling fan speed signal in order to reduce the cooling fan noise and in order to maintain the powertrain cooling requirements. The PCM supplies power and ground to the clutch hall effect sensor of the cooling fan clutch. The hall effect sensor returns a signal pulse through the speed signal circuit in response to the reluctor track, which is located inside the fan clutch. If during operation, the PCM detects a loss of the cooling fan speed signal, DTC P1481 will set.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P1481 Cooling Fan Speed Sensor Circuit
Conditions for Running the DTC
| • | The engine is running. |
| • | System voltage is greater than 8.5 volts. |
Conditions for Setting the DTC
| • | The PCM has detected a loss of cooling fan speed signal. |
| • | The above condition is present for at least 11 seconds. |
Action Taken When the DTC Sets
| • | The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and failed. |
| • | The PCM will store the condition as Freeze Frame/Failure Records data. |
| • | The PCM commands the cooling fan clutch to 100 percent. |
Conditions for Clearing the MIL/DTC
| • | The PCM turns OFF the MIL after the third consecutive trip that the diagnostic test has run and passed. |
| • | The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | Clear the DTC by using the Clear DTC Information function of the scan tool . |
Diagnostic Aids
| • | An inline connector could cause an intermittent DTC. Ensure to test for poor connections and pin retention at all inline connectors. Refer to system schematics for connector and locations. |
| • | If the condition is not present, refer to Testing for Intermittent Conditions and Poor Connections . |
| • | Disconnect the harness connector of the cooling fan clutch from the shroud. Inspect the exposed wires between the harness connector and the tubing. |
| • | Inspect the cooling fan clutch harness in order to ensure that the clutch supply voltage circuit is not shorted to the following circuits: |
| - | The 5-volt reference circuit |
| - | The cooling fan speed signal circuit |
| - | The low reference circuit |
| • | DTC P1481 will set if the engine is started without the drive belt ON. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests for the proper operation of the clutch hall effect sensor.
-
This step tests for the proper operation of the 5-volt reference circuit and of the low reference circuit of the cooling fan.
Step | Action | Values | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Cooling Schematics Connector End View Reference: Cooling System Connector End Views | ||||||||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |||||||
Does the DMM voltage change? | 0-5 V | Go to Step 9 | Go to Step 3 | |||||||
Is the voltage measurement near than the specified value? | 5 V | Go to Step 4 | Go to Step 6 | |||||||
4 |
Does the test lamp illuminate? | -- | Go to Step 5 | Go to Step 8 | ||||||
5 | Test the 5-volt reference circuit of the cooling fan clutch for a high resistance, or for an open. Refer to Circuit Testing and to Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 6 | ||||||
6 | Test the cooling fan speed signal circuit of the cooling fan clutch for a short to ground, for a high resistance, or for an open. Refer to Circuit Testing and to Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 7 | ||||||
7 | Test the cooling fan speed signal circuit of the cooling fan clutch for a short to voltage. Refer to Circuit Testing and to Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 10 | ||||||
8 |
Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 11 | ||||||
9 |
Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 11 | ||||||
10 | Inspect for a poor connection at the harness connector of the cooling fan clutch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs . Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 12 | ||||||
11 | Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs . Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 13 | ||||||
12 | Replace the cooling fan clutch. Refer to Fan Clutch Replacement . Did you complete the replacement? | -- | Go to Step 14 | -- | ||||||
13 | Replace the PCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 14 | -- | ||||||
14 |
Does the DTC reset? | -- | Go to Step 2 | System OK | ||||||
