Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC P0451: Fuel Tank Pressure (FTP) Sensor PerformanceDTC P0452: Fuel Tank Pressure (FTP) Sensor Circuit Low Voltage
DTC P0453: Fuel Tank Pressure (FTP) Sensor Circuit High Voltage
DTC P0454: Fuel Tank Pressure (FTP) Sensor Intermittent
Diagnostic Fault Information
Circuit | Short to Ground | High Resistance | Open | Short to Voltage | Signal Performance |
|---|---|---|---|---|---|
FTP Sensor 5-Volt Reference | P0107, P0452, P0532, P0641 | P0451 | P0452 | P0453, P0641 | -- |
FTP Sensor Signal | P0452 | P0451 | P0452 | P0453 | P0451, P0454 |
FTP Sensor Low Reference | -- | P0446, P0451 | P0446 | -- | -- |
Typical Scan Tool Data
Circuit | Normal Range | Short to Ground | Open | Short to Voltage |
|---|---|---|---|---|
Fuel Tank Pressure Sensor | 1.3-1.7 V | 0 V | 0 V | More than 5 V |
With EVAP system vented to atmosphere and fuel tank temperature stabilized. | ||||
Circuit/System Description
The fuel tank pressure (FTP) sensor measures air pressure or vacuum in the evaporative emission (EVAP) system. The control module supplies a 5-volt reference and a low reference circuit to the FTP sensor. The FTP sensor signal voltage varies depending on EVAP system pressure or vacuum. The controller also uses this FTP signal to determine atmospheric pressure for use in the engine-off small leak test, DTC P0442. Before using this signal as an atmospheric reference it must first be re-zeroed.
Conditions for Running the DTC
P0451
| • | DTC P0451 runs only when the engine-off natural vacuum small leak test, P0442, executes. |
| • | The number of times this test runs can range from 0-2 per engine-off period. The length of the test can be up to 10 minutes. |
P0452 and P0453
DTC P0452 and P0453 run continuously when the ignition is ON.
P0454
| • | DTC P0454 runs only when the engine-off natural vacuum small leak test, P0442, executes. |
| • | This test can run once per engine-off period. The length of the test can be up to 10 minutes. |
| • | A refueling event is not detected. |
Conditions for Setting the DTC
P0451
This DTC will set if the controller is unable to re-zero the FTP sensor voltage within a calibrated range during the engine-off small leak test, P0442.
P0452
The FTP sensor voltage is less than 0.1 volt.
P0453
The FTP sensor voltage is more than 4.9 volts.
P0454
If, during the engine-off natural vacuum small leak test, P0442, the engine control module (ECM) detects an abrupt FTP signal change, other than a refueling event, this DTC will set. An abrupt change is defined as a change of 0.45 inch H2O in the span of 1 second.
Action Taken When the DTC Sets
| • | DTCs P0451 and P0454 are Type A DTCs. |
| • | DTCs P0452 and P0453 are Type B DTCs. |
Conditions for Clearing the MIL/DTC
| • | DTCs P0451 and P0454 are Type A DTCs. |
| • | DTCs P0452 and P0453 are Type B DTCs. |
Diagnostic Aids
| • | Ensure that the reference port on the FTP sensor is unobstructed. |
| • | Scan tool output controls, snapshot, and the plot function can help detect erratic sensor operation. To observe the Fuel Tank Pressure Sensor signal under vacuum conditions, use the Quick Snapshot and the EVAP Purge/Seal function to capture data while commanding purge to 20 percent. Then plot the data to look for erratic sensor operation. A similar test can be done for the pressure side of the sensor range by applying pressure with J 41413-200 Evaporative Emission System Tester (EEST) while taking a snapshot with the scan tool. |
Reference Information
Schematic Reference
Connector End View Reference
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Special Tools Required
J 41413-200 Evaporative Emissions System Tester (EEST)
Circuit/System Verification
- Remove the fuel cap.
- Ignition ON, engine OFF.
- Observe the Fuel Tank Pressure Sensor parameter with a scan tool.
- The FTP Sensor parameter should be 1.3-1.7 volts.
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the FTP sensor.
- Ignition OFF, ensure that the ECM completely powers down and test for less than 5 ohms of resistance between the low reference circuit terminal A and ground.
- Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal C and ground.
- Verify the scan tool FTP sensor parameter is less than 0.2 volt.
- Install a 3A fused jumper wire at the signal circuit terminal B and the 5-volt reference circuit terminal C. Verify the scan tool FTP sensor voltage parameter is greater than 4.7 volts.
- If all circuits test normal, replace the FTP sensor.
| ⇒ | If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the control module. |
| ⇒ | If less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the control module. |
| ⇒ | If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the control module. |
| ⇒ | If greater than the specified range, test the signal circuit terminal B for a short to voltage. If the circuit tests normal, replace the control module. |
| ⇒ | If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the control module. |
Repair Instructions
| • | For DTC P0452 or P0453, perform the Diagnostic Repair Verification after completing the diagnostic procedure. |
| • | For DTC P0451 or P0454, clear DTCs with a scan tool. |
| • | Control Module References for ECM replacement, setup, and programming |
