GM Service Manual Online
For 1990-2009 cars only

Inspection Procedure


    Object Number: 7628  Size: SH
  1. Inspect the valve body to spacer plate gasket for valve body channel witness marks. The witness marks should be complete. Incomplete witness marks may be caused by an uneven case surface. Incomplete witness marks may also be caused by cross-channel leaks.
  2. Inspect the valve body casting for the following conditions:
  3. • Porosity
    • Cracks
    • Damaged machined surfaces
    • Chips or debris

Cleaning Procedure

  1. Clean all the valves, springs, bushings, and the control valve body in clean solvent.
  2. Dry all the parts using compressed air.

Installation Procedure

    Caution: Refer to Valve Springs Can Be Tightly Compressed Caution in the Preface section.


    Object Number: 736214  Size: SH

    Important: Lubricate all parts with Dexron®-lll automatic transmission fluid before installation.

  1. Install the following items:
  2. 1.1. The isolator valve (398)
    1.2. The regulator apply spring (397)
    1.3. The regulator apply valve (380)
    1.4. The bore plug (381)
    1.5. The bore plug retainer (395)

    Object Number: 405094  Size: SH
  3. Install the following items:
  4. 2.1. The 4-3 sequence valve spring (382)
    2.2. The 4-3 sequence valve (383)
    2.3. The 3-4 relay valve (384)
    2.4. The bore plug (381)
    2.5. The bore plug retainer (395)

    Object Number: 405092  Size: SH
  5. Install the following items:
  6. 3.1. The 3-4 shift valve (385)
    3.2. The 3-4 shift valve spring (386)
    3.3. The bore plug (381)
    3.4. The bore plug retainer (395)

    Object Number: 405086  Size: SH
  7. Install the following items:
  8. 4.1. The reverse abuse valve (387)
    4.2. The reverse abuse valve spring (388)
    4.3. The bore plug (359)
    4.4. The coiled spring pin (360)
    4.5. The 3-2 downshift valve (389)
    4.6. The 3-2 downshift valve spring (390)
    4.7. The bore plug (381)
    4.8. The bore plug retainer (395)

    Object Number: 405083  Size: SH
  9. Install the following items:
  10. 5.1. The 3-2 control valve spring (392)
    5.2. The 3-2 control valve (391)
    5.3. The 3-2 control solenoid (394)
    5.4. The solenoid retainer (395)

    Object Number: 405080  Size: SH
  11. Install the following items:
  12. 6.1. The actuator feed limit valve (374)
    6.2. The actuator feed limit valve spring (375)
    6.3. The bore plug (376)
    6.4. The bore plug retainer (395)
    6.5. The pressure control solenoid (377)
    6.6. The solenoid retainer (378)
    6.7. The solenoid retainer bolt (364)

    Object Number: 13144  Size: SH
  13. Install the following items:
  14. 7.1. The 1-2 accumulator valve spring (370)
    7.2. The 1-2 accumulator valve (371) in the 1-2 accumulator valve sleeve (372)
    7.3. The 1-2 accumulator valve and sleeve assembly
    7.4. The coiled spring pin (360)

    Object Number: 405074  Size: SH
  15. Install the following items:
  16. 8.1. The 2-3 shift valve (368)
    8.2. The 2-3 shuttle valve (369)
    8.3. The 2-3 shift solenoid valve (367B)
    8.4. The solenoid retainer (395)

    Object Number: 405071  Size: SH
  17. Install the following items:
  18. 9.1. The 1-2 shift valve spring (365)
    9.2. The 1-2 shift valve (366)
    9.3. The 1-2 shift solenoid valve (367A)
    9.4. The solenoid valve retainer (395)

    Object Number: 13239  Size: SH
  19. Install the following items:
  20. 10.1. The forward abuse valve (357)
    10.2. The forward abuse valve spring (358)
    10.3. The bore plug (359)
    10.4. The coiled spring pin (360)
    10.5. The low overrun valve (361)
    10.6. The low overrun valve spring (362)
  21. Install the following items:
  22. 11.1. The forward accumulator oil seal (353) on the forward accumulator piston (354)
    11.2. The forward accumulator pin (355)
    11.3. The forward accumulator piston (354)
    11.4. The forward accumulator spring (356)
    11.5. The forward accumulator cover (363)
    11.6. The forward accumulator cover bolts (364)

    Object Number: 13146  Size: SH
  23. Install the manual valve (340).

Inspection Procedure


    Object Number: 7628  Size: SH
  1. Inspect the valve body to spacer plate gasket for valve body channel witness marks. The witness marks should be complete. Incomplete witness marks may be caused by an uneven case surface. Incomplete witness marks may also be caused by cross-channel leaks.
  2. Inspect the valve body casting for the following conditions:
  3. • Porosity
    • Cracks
    • Damaged machined surfaces
    • Chips or debris

Cleaning Procedure

  1. Clean all the valves, springs, bushings, and the control valve body in clean solvent.
  2. Dry all the parts using compressed air.

Installation Procedure

    Caution: Refer to Valve Springs Can Be Tightly Compressed Caution in the Preface section.


    Object Number: 736214  Size: SH

    Important: Lubricate all parts with DEXRON®lll automatic transmission fluid before installation.

  1. Install the following items:
  2. 1.1. The isolator valve (398)
    1.2. The regulator apply spring (397)
    1.3. The regulator apply valve (380)
    1.4. The bore plug (381)
    1.5. The bore plug retainer (395)

    Object Number: 405094  Size: SH
  3. Install the following items:
  4. 2.1. The 4-3 sequence valve spring (382)
    2.2. The 4-3 sequence valve (383)
    2.3. The 3-4 relay valve (384)
    2.4. The bore plug (381)
    2.5. The bore plug retainer (395)

    Object Number: 405092  Size: SH
  5. Install the following items:
  6. 3.1. The 3-4 shift valve (385)
    3.2. The 3-4 shift valve spring (386)
    3.3. The bore plug (381)
    3.4. The bore plug retainer (395)

    Object Number: 405086  Size: SH
  7. Install the following items:
  8. 4.1. The reverse abuse valve (387)
    4.2. The reverse abuse valve spring (388)
    4.3. The bore plug (359)
    4.4. The coiled spring pin (360)
    4.5. The 3-2 downshift valve (389)
    4.6. The 3-2 downshift valve spring (390)
    4.7. The bore plug (381)
    4.8. The bore plug retainer (395)

    Object Number: 405083  Size: SH
  9. Install the following items:
  10. 5.1. The 3-2 control valve spring (392)
    5.2. The 3-2 control valve (391)
    5.3. The 3-2 control solenoid (394)
    5.4. The solenoid retainer (395)

    Object Number: 1239566  Size: SH
  11. Install the following items:
  12. 6.1. The actuator feed limit valve (374)
    6.2. The actuator feed limit valve spring (375)
    6.3. The bore plug (376)
    6.4. The bore plug retainer (395)
    6.5. The pressure control solenoid (377)
       • 1 - Colorado/Canyon
       • 2 - All other models
    6.6. The solenoid retainer (378)

    Notice: Refer to Fastener Notice in the Preface section.

    6.7. The solenoid retainer bolt (364)

    Tighten
    Tighten the bolt to 8-14 N·m (6-10 lb ft).


    Object Number: 13144  Size: SH
  13. Install the following items:
  14. 7.1. The 1-2 accumulator valve spring (370)
    7.2. The 1-2 accumulator valve (371) in the 1-2 accumulator valve sleeve (372)
    7.3. The 1-2 accumulator valve and sleeve assembly
    7.4. The coiled spring pin (360)

    Object Number: 405074  Size: SH
  15. Install the following items:
  16. 8.1. The 2-3 shift valve (368)
    8.2. The 2-3 shuttle valve (369)
    8.3. The 2-3 shift solenoid valve (367B)
    8.4. The solenoid retainer (395)

    Object Number: 405071  Size: SH
  17. Install the following items:
  18. 9.1. The 1-2 shift valve spring (365)
    9.2. The 1-2 shift valve (366)
    9.3. The 1-2 shift solenoid valve (367A)
    9.4. The solenoid valve retainer (395)

    Object Number: 13239  Size: SH
  19. Install the following items:
  20. 10.1. The forward abuse valve (357)
    10.2. The forward abuse valve spring (358)
    10.3. The bore plug (359)
    10.4. The coiled spring pin (360)
    10.5. The low overrun valve (361)
    10.6. The low overrun valve spring (362)
  21. Install the following items:
  22. 11.1. The forward accumulator oil seal (353) on the forward accumulator piston (354)
    11.2. The forward accumulator pin (355)
    11.3. The forward accumulator piston (354)
    11.4. The forward accumulator spring (356)
    11.5. The forward accumulator cover (363)
    11.6. The forward accumulator cover bolts (364)

    Object Number: 13146  Size: SH
  23. Install the manual valve (340).