DTC C0300. Isuzu Ascender

For 1990-2009 cars only

Makes 🢒 Isuzu 🢒 2005 🢒 Ascender - 4WD 🢒 Driveline/Axle 🢒 Transfer Case - NVG 226-NP8 🢒 DTC C0300

Circuit Description

The rear propshaft speed sensor is a permanent magnet generator. The permanent magnet generator produces a pulsing AC voltage. The AC voltage level and number of pulses increase as speed increases. The module converts the pulsating AC voltage to a propshaft RPM which is used for calculations. The propshaft RPM can be displayed with a scan tool.

This DTC detects an open, short to ground, short to voltage or faulty sensor.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC C0300 Rear Speed Sensor Malfunction

Conditions for Running the DTC

•	The ignition is ON.

•	System voltage is 9-18 volts.

•	Vehicle speed exceeds 16 km/h (10 mph).

Conditions for Setting the DTC

The system logs the DTC if the rear propshaft input indicates a speed of less than 16 RPM for 30 seconds while all of the following are true:

•	The transmission is NOT in PARK/NEUTRAL.

•	The engine is running.

•	The front axle is engaged.

•	Vehicle speed on Class 2 data bus exceeds 16 km/h (10 mph).

Action Taken When the DTC Sets

•	All shifts to AUTO or the Adapt mode, is disabled. If the current mode is AUTO, the system does not allow any further adaptive events, such as correcting slip.

•	The SERVICE 4WD indicator remains illuminated for the remainder of the current ignition cycle.

Conditions for Clearing the DTC

•	The transfer case shift control module clears the DTC if the condition for setting the DTC is not currently present.

•	A history DTC clears after 100 consecutive ignition cycles without a fault present.

•	History DTCs can be cleared using a scan tool.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

This step tests to see if the malfunction is intermittent.

This step tests the internal resistance of the propshaft speed sensor.

This step tests to see if the propshaft speed sensor can generate a sufficient amount of AC voltage.

This step tests the rear propshaft speed sensor low circuit for a short to ground, a high resistance or an open.

This step tests the rear propshaft speed sensor high circuit for a short to ground, a high resistance or an open.

This step tests the rear propshaft speed sensor low circuit for a short to voltage.

This step tests the rear propshaft speed sensor high circuit for a short to voltage.

This step tests the rear propshaft speed sensor low circuit for a short to the rear propshaft sensor high circuit.

Step	Action	Values	Yes	No
Schematic Reference: Transfer Case Control Schematics Connector End View Reference: Transfer Case Control Connector End Views
1	Did you perform the Diagnostic System Check - Vehicle?	--	Go to Step 2	Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2	Drive the vehicle for a short test drive. With the scan tool, observe the value of the Rear Propshaft Speed Data Parameter in the Transfer Case Data List, while driving. Does the RPM value vary or become intermittent while driving at a steady speed?	--	Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems	Go to Step 3
3	Turn the ignition OFF. Disconnect the transfer case rear propshaft speed sensor. Measure the resistance of the transfer case rear propshaft speed sensor. Is the resistance reading within the specified values?	1,300-2,700 ohms	Go to Step 4	Go to Step 10
4	Connect a DMM to the transfer case rear propshaft speed sensor. Block the front wheels. Place the transmission in NEUTRAL. Raise and support the rear axle, so that the wheels turn freely. Hold one rear wheel while rotating the other rear wheel. Observe the AC voltage reading on the DMM Is the voltage reading greater than the specified value?	0.5 V AC	Go to Step 5	Go to Step 10
5	Disconnect the transfer case shift control module. Test the rear propshaft speed sensor low signal circuit for a short to ground, a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition?	--	Go to Step 12	Go to Step 6
6	Test the rear propshaft speed sensor high signal circuit for a short to ground, a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition?	--	Go to Step 12	Go to Step 7
7	Test the rear propshaft speed sensor low signal circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition?	--	Go to Step 12	Go to Step 8
8	Test the rear propshaft speed sensor high signal circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition?	--	Go to Step 12	Go to Step 9
9	Test the rear propshaft speed sensor high signal circuit for a short to the rear propshaft sensor low signal circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition?	--	Go to Step 12	Go to Step 11
10	Replace the transfer case rear propshaft speed sensor. Refer to Transfer Case Rear Output Shaft Speed Sensor Replacement - Right Side . Did you complete the repair?	--	Go to Step 12	--
11	Important : After transfer case shift control module replacement and reprogramming, ensure all doors are closed and the key is out of the ignition, then open and close the doors again and wait 2 minutes to avoid incomplete programming or false communication DTCs. Replace the transfer case shift control module. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the repair?	--	Go to Step 12	--
12	Use the scan tool in order to clear the DTCs. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text. Does the DTC set?	--	Go to Step 2	System OK