The intake flow rationality diagnostic provides the within-range rationality check for the mass air flow (MAF), manifold absolute pressure (MAP), and the throttle position (TP) sensors. This is an explicit model-based diagnostic containing 4 separate models for the intake system.

The estimates of MAF and MAP obtained from this system of models and calculations are then compared to the actual measured values from the MAF, MAP, and the TP sensors and to each other to determine the appropriate DTC to fail. The following table illustrates the possible failure combinations and the resulting DTC or DTCs.

The ECM detects that the actual measured airflow from MAF, MAP, and TP is not within range of the calculated airflow that is derived from the system of models for more than 2 seconds.

DTC P0106 is a Type B DTC.

DTC P0106 is a Type B DTC.

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Special Tools

1. Verify that DTC P0641 or P0651 is not set.

⇒	If any of the DTCs are set, refer to DTC P0641 or P0651.

2. Verify that restrictions do not exist in the exhaust system. Refer to Restricted Exhaust.
3. Ignition OFF for 90 seconds, determine the current vehicle testing altitude.
4. Ignition ON, engine OFF, observe the scan tool BARO parameter. Compare the parameter to the Altitude Versus Barometric Pressure table. The BARO parameter should be within the specified range indicated in the table.
5. Use the scan tool and compare the MAP Sensor parameter to a known good vehicle, under various operating conditions. The readings should be within 5 kPa of the known good vehicle.
6. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

1. Verify the integrity of the entire air induction system by inspecting for the following conditions:

•	Any damaged components

•	Loose or improper installation

•	An air flow restriction

•	Any vacuum leak

•	Improperly routed vacuum hoses

•	In cold climates, inspect for any snow or ice buildup

•	Verify that restrictions do not exist in the MAP sensor port or vacuum source.

2. Ignition OFF for 90 seconds, disconnect the harness connector at the MAP sensor.
3. Test for less than 5 ohms between the low reference circuit terminal 2 and ground.

⇒	If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

4. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 1 and ground.

⇒	If less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.

⇒	If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ECM.

5. Verify the scan tool MAP Sensor parameter is less than 1 kPa.

⇒	If greater than the specified range, test the signal circuit terminal 3 for a short to voltage. If the circuit tests normal, replace the ECM.

6. Install a 3A fused jumper wire between the signal circuit terminal 3 and the 5-volt reference circuit terminal 1. Verify the scan tool MAP Sensor parameter is greater than 126 kPa.

⇒	If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.

7. If the circuits test normal, test or replace the MAP sensor.

Skewed Signal Test

1. Using the following steps and referencing the table below will determine if the MAP sensor is skewed.
2. Ignition ON, engine OFF, observe the MAP Sensor Scan Tool parameter.
3. Use the observed MAP Sensor Scan Tool parameter that is closest to a value that is indicated in the first column.

THEN

4. Using the J 23738-A or the J 35555 to apply 5 in Hg of vacuum to the MAP sensor, the parameter in the first column should decrease by 17 kPa. The acceptable range is indicated in the second column.
5. Using the J 23738-A or the J 35555 to apply 10 in Hg of vacuum to the MAP sensor, the parameter in the first column should decrease by 34 kPa. The acceptable range is indicated in the third column.

Erratic Signal Test

1. Ignition OFF, remove the MAP sensor.
2. Install a 3A fused jumper wire between the 5-volt reference circuit terminal 1 and the corresponding terminal of the MAP sensor.
3. Install a jumper wire between the low reference circuit terminal 2 of the MAP sensor and ground.
4. Install a jumper wire at terminal 3 of the MAP sensor.
5. Connect a DMM between the jumper wire from terminal 3 of the MAP sensor and ground.
6. Ignition ON, install the J 23738-A or J 35555 to the MAP sensor vacuum port. Slowly apply vacuum to the sensor while observing the voltage on the DMM. The voltage should vary between 0-5.2 volts without any spikes or dropouts.

⇒	If the voltage reading is erratic, replace the MAP sensor.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.