- Remove all mounds or loose pieces of urethane adhesive from pinch weld areas.
- Remove all but 2 mm (3/64 in) of the existing urethane adhesive from the pinch weld flange.
- If the original window is being reused, remove all but a thin film of the existing urethane adhesive from the window surface by using a clean utility knife or razor blade scraper.
- Inspect for any of the following problems in order to help prevent future breakage of the window:
• | Solder spots on the pinchweld |
• | Any other obstruction or irregularity in the pinch-weld flange |
Important: If corrosion of the pinch weld flange is present or if sheet metal repairs or replacement are required, the pinch weld flange must be refinished in order to restore the bonding area strength. If paint repairs are required,
mask the flange bonding area prior to applying the color coat in order to provide a clean primer only surface. Materials such as BASF DE15, Dupont 2610, Sherwin-Williams PSE 4600 and NP70, Martin-Semour 5120 and 5130, PPG DP90LF, Spies/Hecker 3688/8590 3688/5150
4070/5090, and Standox 11158/13320 14653/14980 are products approved for this application.
- After repairing the opening as indicated, perform the following steps:
5.1. | Remove all traces of broken glass from the outer cowl panel, seats, floor and defroster ducts. |
5.2. | Clean around the edge of the inside surface of the window with a 50/50 mixture of isopropyl alcohol and water by volume on a dampened lint free cloth. |
Caution: When replacing stationary windows, use Urethane Adhesive Kit GM P/N 12346392
(Canadian P/N 10952983), or a urethane adhesive system meeting GM Specification
GM3651G, to maintain original installation integrity. Failure to use the urethane
adhesive kit will result in poor retention of the window which may allow unrestrained
occupants to be ejected from the vehicle resulting in personal injury.
- Verify all primers and urethane adhesives are within expiration dates.
Caution: Failure to prep the area prior to the application of primer
may cause insufficient bonding of urethane adhesive. Insufficient bonding
of urethane adhesive may allow unrestrained occupants to be ejected from
the vehicle resulting in personal injury.
Important: Do not apply the black #3 primer to the existing bead of urethane adhesive on the pinch weld flange. Apply the primer only to nicks, scratches or the primed surfaces.
- Shake the black #3 primer for at least 1 minute.
- Use a dauber in order to apply the primer to the surface of the pinch weld flange.
- Allow the pinch weld primer to dry for approximately 10 minutes.
- With the aid of an assistant, dry fit the window to the opening in order to determine the correct position.
- Use masking tape in order to mark the locations (1) of the window (2) in the opening.
- Cut the masking tape in the center and remove the window from the opening.
Important: Use care when applying glass prep clear #1 on the window. This primer dries almost instantly, and may stain the viewing area of the window if not applied evenly.
- Use a new dauber in order to apply glass prep clear #1 to the area approximately 10-16 mm (3/8-5/8 in) around the entire perimeter of the window inner surface.
Immediately wipe the glass primed area using a
clean, lint-free cloth.
- Apply a second coat of the glass prep clear #1 to the same area of the glass.
Note: The glass primer black #2 is effective up to 8 hours after applying it to the glass. The primed surface of the glass must be kept clean.
- Shake the glass primer black #2 for at least 1 minute.
- Use a new dauber in order to apply the glass primer black #2 to the same areas (2) that glass prep clear #1 was applied.
- Use the inside edge of the window as a guide for the nozzle in order to apply the urethane adhesive bead to the window bonding surface.
- Use a cartridge-type caulking gun in order to apply a smooth, continuous bead of urethane adhesive.
- Use the edge of the window as a guide for the nozzle in order to apply the urethane adhesive (1) to the inner
surface of the window (3).
- Align the masking tape lines on the window and the body.
- Place the window assembly into the bodyside opening. Ensure that the window alignment pins are properly aligned
to the bodyside.
- Tape the window to the body in order to minimize movement until the urethane adhesive cures.
- Firmly press around the entire periphery of the exterior window in order to ensure proper adhesion to the body.
- Clean any excess urethane adhesive from the body and interior trim panels.
Important: Do not direct a stream of high pressure water to the freshly applied urethane adhesive.
- Use a soft spray of warm water in order to immediately water test the bodyside window.
- Inspect the window for leaks.
- If any leaks are found, use a plastic paddle in order to apply extra urethane adhesive at the leak point.
- Retest the window for leaks.
Caution: Insufficient curing of urethane adhesive may allow unrestrained occupants
to be ejected from the vehicle resulting in personal injury.
• | For the moisture-curing type of urethane adhesive, allow a minimum
of 6 hours at 21°C (70°F) or greater and with at least 30 percent
relative humidity. Allow at least 24 hours for the complete curing
of the urethane adhesive. |
• | For the chemical-curing type of urethane adhesive, allow a minimum
of 1 hour . |
Do NOT physically disturb the repair area until after these minimum
times have elapsed.
- Maintain the following conditions in order to properly cure the urethane adhesive.
• | Partially lower a door window in order to prevent pressure buildups when closing doors before the urethane cures. |
• | Do not drive the vehicle until the urethane adhesive is cured. Refer to the above curing times. |
• | Do not use compressed air in order to dry urethane adhesive. |
• | Do not cycle the actuator until after the minimum curing times have elapsed. |