GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Isuzu 🢒 2008 🢒 I-370 🢒 Transmission/Transaxle 🢒 Automatic Transmission - 4L60-E/4L65-E/4L70-E 🢒 Transfer Case Assembly Replacement

Removal Procedure

  1. Drain the transfer case fluid, if necessary. Refer to Transfer Case Fluid Replacement .
  2. Remove the rear propeller shaft. Refer to One-Piece Propeller Shaft Replacement .
  3. Remove the front propeller shaft. Refer to Front Propeller Shaft Replacement .
  4. Remove the transfer case encoder motor. Refer to Transfer Case Encoder Motor Replacement .

    5. Object Number: 1313605 Size: SH
  5. Disconnect the engine wiring harness electrical connectors (3, 5) from the following:
    6. • The speed sensor (2)
    • The heated oxygen sensor pigtail

    Object Number: 1313610 Size: SH
  6. Disconnect the engine wiring harness electrical connectors (1, 2) from the following:
    7. • The brown NEUTRAL switch electrical connector (6)
    • The gray 2/4 indicator switch electrical connector (4)
  7. Disconnect the engine wiring harness retainers from the transfer case.
  8. Position the engine wiring harness aside.

    9. Object Number: 1313616 Size: SH
  9. If equipped with (MA5) complete the following:
    10. 9.1. Remove the transfer case mounting bolts.
    9.2. With the aid of an assistant, carefully lower the transfer case from the vehicle.

    Object Number: 1313617 Size: SH
  10. If equipped with (M30) complete the following:
    11. 10.1. Remove the transfer case mounting bolts.
    10.2. With the aid of an assistant, carefully lower the transfer case from the vehicle.

Installation Procedure

    Object Number: 1313617 Size: SH
  1. If equipped with (M30) complete the following:
    2. 1.1. With the aid of an assistant, carefully raise the transfer case to the transfer case adapter, aligning the splines.

    Notice: Refer to Fastener Notice in the Preface section.

    1.2. Install the transfer case mounting bolts.

    Tighten
    Tighten the transfer case mounting bolts to 50 N·m (37 lb ft).


    Object Number: 1313616 Size: SH
  2. If equipped with (MA5) complete the following:
    3. 2.1. Lightly lubricate the transmission rear seal.

            Important: Do not catch the input shaft on the transmission rear seal.

    2.2. With the aid of an assistant, carefully raise the transfer case to the manual transmission, aligning the splines.
    2.3. Install the transfer case mounting bolts.

    Tighten
    Tighten the transfer case mounting bolts to 50 N·m (37 lb ft).


    Object Number: 1313610 Size: SH
  3. Position the engine wiring harness (3) to the transfer case assembly.
  4. Connect the engine wiring harness retainers to the transfer case.
  5. Connect the engine wiring harness electrical connectors (1, 2) to the following:
    6. • The brown NEUTRAL switch electrical connector (6)
    • The gray 2/4 indicator switch electrical connector (4)

    Object Number: 1313605 Size: SH
  6. Connect the engine wiring harness electrical connectors (3, 5) to the following:
    7. • The speed sensor (2)
    • The heated oxygen sensor pigtail
  7. Install the transfer case encoder motor. Refer to Transfer Case Encoder Motor Replacement .
  8. Install the front propeller shaft. Refer to Front Propeller Shaft Replacement .
  9. Install the rear propeller shaft. Refer to One-Piece Propeller Shaft Replacement .
  10. Fill the transfer case with fluid, if previously drained. Refer to Transfer Case Fluid Replacement .