GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Isuzu 🢒 2008 🢒 I-370 🢒 Power and Signal Distribution 🢒 Wiring Systems and Power Management 🢒 DTC P0324, P0325, P0326, P0327, or P0328

Diagnostic Instructions
    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provide an overview of each diagnostic category.

DTC Descriptors

DTC P0324: Knock Sensor (KS) Module Performance

DTC P0325: Knock Sensor (KS) Circuit

DTC P0326: Knock Sensor (KS) Performance

DTC P0327: Knock Sensor (KS) Circuit Low Voltage

DTC P0328: Knock Sensor (KS) Circuit High Voltage

Diagnostic Fault Information

Circuit

Short to Ground

High Resistance

Open

Short to Voltage

Signal Performance

Knock Sensor Signal

P0327, P0328

P0325

P0325

P0327, P0328

P0326

Circuit/System Description

The knock sensor (KS) system enables the engine control module (ECM) to control the ignition timing for the best possible performance while protecting the engine from potentially damaging levels of detonation. The KS is located on the intake side of the engine block. The KS produces an AC voltage signal that varies depending on the vibration level during engine operation. The ECM receives the KS signal through 2 isolated signal circuits. The ECM adjusts the spark timing based on the amplitude and the frequency of the KS signal.

Conditions for Running the DTC

DTC P0324

This DTC runs continuously when the engine speed is greater than or equal to 1,800 RPM and engine load is greater than a calibrated amount.

DTC P0326

This DTC runs continuously when:

    • The engine speed is greater than or equal to 1,800 RPM.
    • The manifold absolute pressure (MAP) is greater than 55 kPa.
    • DTCs P0120, P0121, P0122, or P0123 are not set.

DTCs P0325, P0327, P0328

These DTCs run continuously when:

    • The engine coolant temperature (ECT) is greater than -40°C (-40°F).
    • The engine run time is greater than 2 minutes.

Conditions for Setting the DTC

P0324

The ECM has detected an internal circuitry fault.

P0325

The KS signal circuits are open or shorted together for 6 seconds.

P0326

    • The KS signal indicates an excessive engine knock is present.
    • The ECM commanded spark retard at a given engine load and speed is more than the calibrated value.
    • The above conditions exist for 6 seconds.

P0327 and P0328

The KS signal circuits are shorted to ground or power.

Action Taken When the DTC Sets

DTCs P0324, P0325, P0326, P0327, and P0328 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0324, P0325, P0326, P0327, and P0328 are Type B DTCs.

Diagnostic Aids
    • Inspect the KS for physical damage. A KS that is dropped or damaged may cause a DTC to set.
    • Inspect the KS for proper installation. A KS that is loose or over torqued may cause a DTC to set. The KS should be free of thread sealant.
    • The KS mounting surface should be free of burrs, casting flash, and foreign material.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Knock Sensor (KS) System Description

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs
    •  Measuring Frequency

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Testing

P0324

    • If DTC P0327 and P0328 are also set, preform those diagnostics first.
    • This DTC indicates an internal control module circuitry failure. Replace the ECM.

P0325, P0327, and P0328

  1. Ignition ON, engine OFF.
  2. Disconnect the KS harness connector.
  3. Measure for 2-5 volts between each of the following circuits and ground on the ECM side of the harness connector.
    4. • The KS signal circuit, terminal A
    • The KS signal circuit, terminal B
    ⇒If less than the specified range, test the circuits for a short to ground or an open/high resistance. If the circuits test normal, replace the ECM.
    ⇒If greater than the specified range, test the circuits for a short to voltage. If the circuits test normal, replace the ECM.
  4. If the circuits test normal, replace the KS.

P0326

       Important: If DTC P0335 or P0336 are also set, diagnose those DTCs first.

    • Inspect for a loose or broken vehicle accessory or accessory bracket.
    • Inspect for excessive engine mechanical noise.

Component Testing
  1. Connect the DMM between the KS signal circuit terminal A and the KS signal circuit terminal B on the sensor side of the KS harness connector.
  2. Set the DMM to the 400 mV AC hertz scale and wait for the DMM to stabilize at 0 Hz.

    3. Important: DO NOT tap on plastic engine components.

  3. Tap on the engine block with a non-metallic object near the KS while observing the signal indicated on the DMM.
  4. The DMM should display a fluctuating frequency while tapping on the engine block.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Knock Sensor 1 Replacement
    •  Symptoms - Engine Controls
    •  Symptoms - Engine Mechanical
    •  Control Module References for ECM replacement, setup, and programming