The engine control module (ECM) monitors fuel rail pressure (FRP) using the FRP sensor. If the sensor indicates a pressure more than the commanded rail pressure, plus a possible transitional overshoot, the ECM will set DTC P0088 for fuel rail pressure too high.
This diagnostic procedure supports the following DTC:
DTC P0088 Fuel Rail Pressure (FRP) Too High
• | The engine coolant temperature (ECT) is between 30-100°C (86-212°F). |
• | The fuel temperature is between 20-80°C (68-176°F). |
• | The deviation of rail pressure is less than 5 MPa (725 psi). |
• | The deviation of engine speed is less than 50 RPM. |
• | The above conditions are met for 5 seconds. |
• | The engine is running. |
• | The battery voltage is between 10-16 volts. |
• | Commanded fuel supply is 0 mm³/stroke. |
• | Actual fuel rail pressure is higher than desired pressure 10 MPa (1,450 psi). |
• | The above conditions are met for 22 seconds. |
• | The ECM illuminates the malfunction indicator lamp (MIL) and reduced engine power indicator lamp, if equipped, when the diagnostic runs and fails. |
• | The ECM records the operating conditions at the time the diagnostic fails. The ECM stores this information in the Failure Records. |
• | The ECM limits accelerator operating range. |
• | The ECM limits fuel injection quantity. |
• | The ECM limits fuel rail pressure. |
• | The ECM closes the exhaust gas recirculation (EGR) valve and stops EGR control. |
• | The ECM inhibits cruise control. |
• | The MIL resets when the ignition is turned OFF. |
• | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
• | Clear the MIL and the DTC with a scan tool. |
Important: The Actual Fuel Rail Pressure on the scan tool will only update with the engine running or one time after the key is cycled when the ignition has been turned OFF for more than 10 seconds.
• | An intermittently sticking suction control valve (SCV) may have allowed the fuel pressure to become high enough to set this DTC. |
• | Normal actual fuel rail pressure readings on the scan with the engine running Park or Neutral at idle are 25-35 MPa (3,650-5,050 psi) and 60-130 MPa (8,700-18,850 psi) in Park or Neutral at WOT, accelerator pedal full travel. |
• | A skewed FRP sensor value, shifted to a higher pressure, can set this DTC. The actual fuel rail pressure on the scan tool should read 0 MPa (0 psi) with the key ON and the engine OFF after the engine has stopped running for a minimum of 2 minutes. |
• | Resistance in the FRP sensor low reference circuit can set this DTC. Ensure that the sensor low reference circuit has no resistance and the connectors are tight and free of corrosion. |
Step | Action | Values | Yes | No | ||||
---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics | ||||||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |||||
2 |
Did the DTC fail this ignition? | -- | Go to Step 3 | Go to Intermittent Conditions | ||||
3 |
Did the DTC fail this ignition? | -- | Go to Step 13 | Go to Step 4 | ||||
4 |
Was a condition found? | -- | Go to Step 13 | Go to Step 5 | ||||
5 |
Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 6 | ||||
6 |
Is the fuel parameter near the specified value? | 0 MPa | Go to Step 7 | Go to Step 9 | ||||
7 |
Is the parameter within the specified range? | 25-40 MPa (3,626-5,801 psi) | Go to Step 8 | Go to Step 9 | ||||
8 |
Was a condition found? | -- | Go to Step 12 | Go to Step 11 | ||||
9 | Replace the fuel rail assembly. Did you complete the replacement? | -- | Go to Step 13 | -- | ||||
10 | Review the DTC.
Is the DTC current? | -- | Go to Step 11 | Go to Step 13 | ||||
11 | Replace the supply pump assembly. Did you complete the replacement? | -- | Go to Step 13 | -- | ||||
12 |
Important: The replaced ECM must be programmed. Replace the ECM. Refer to Engine Control Module Programming and Setup , Engine Control Module Replacement/Restore Fuel Rate Data , and Fuel Injector Flow Rate Programming . Did you complete the replacement? | -- | Go to Step 13 | -- | ||||
13 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 14 | ||||
14 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | System OK |