Circuit Description
The engine control module (ECM), the electronic brake control module (EBCM), and the transmission control module (TCM) communicate control and diagnostic information via a controller area network (CAN) communication bus. The ECM monitors CAN operational status by expecting a constant flow of messages from the EBCM and the TCM. If the ECM fails to receive an expected message from one of the other modules, DTC U2104, U2106, or U2108 will set, depending on what communication is lost.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC U2106 Lost Communications With Transmission Control System
Conditions for Running the DTC
| • | The ignition is ON. |
| • | The module supply voltage is in the normal operating range of 9-16 volts. |
Conditions for Setting the DTC
The CAN message from the TCM is not received by the ECM for 200 milliseconds.
Action Taken When the DTC Sets
The control module will not illuminate the malfunction indicator lamp (MIL) when the diagnostic runs and fails.
Conditions for Clearing the MIL/DTC
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | Clear the DTC with a scan tool. |
Diagnostic Aids
The modules that communicate on the CAN system are wired parallel to each other until the respective circuits are spliced together for the ECM. An open in the CAN circuits of one module will not affect the other module. A short to ground or short to voltage affects all modules no matter where the failure occurs.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
If the fault is a short to ground, a short together, or an open between the ECM and the CAN circuit splices, DTC U2104 will also set. These failures affect the entire system.
-
This test is for an open in the CAN HI circuit that will only affect the TCM communications.
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Engine Controls Schematics for the 7.8L engine Connector End View Reference: Computer/Integrating Systems Connector End Views | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | |
Did DTC U2104 also set? | Go to DTC U2104 | Go to Step 3 | |
3 |
Does the DTC fail this ignition? | Go to Step 4 | Go to Intermittent Conditions for the 7.8L engine |
Did the CAN high circuit test open? | Go to Step 12 | Go to Step 5 | |
5 | Test the CAN low circuit for an open between the CAN harness splice and the TCM. Refer to Testing for Continuity . Did the CAN low circuit test open? | Go to Step 13 | Go to Step 6 |
6 | Test for greater than 50 ohms between the CAN high and CAN low circuits. Refer to Troubleshooting with a Digital Multimeter . Is the resistance greater than 50 ohms? | Go to Step 7 | Go to Step 16 |
7 | Probe the CAN high circuit with a test lamp connected to battery voltage. Refer to Troubleshooting with a Test Lamp . Does the test lamp illuminate? | Go to Step 15 | Go to Step 8 |
8 |
Does the test lamp illuminate? | Go to Step 14 | Go to Step 9 |
9 | Probe the CAN low circuit with a test lamp connected to a good ground. Does the test lamp illuminate? | Go to Step 18 | Go to Step 10 |
10 | Probe the CAN low circuit with a test lamp connected to the battery voltage. Does the test lamp illuminate? | Go to Step 17 | Go to Step 11 |
11 | Test for an intermittent or poor connection at the TCM. Repair as necessary. Refer to Testing for Intermittent Conditions and Poor Connections and Wiring Repairs . Did you find and correct the condition? | Go to Step 20 | Go to Step 19 |
12 | Repair the open in the CAN high circuit between the TCM and the CAN splice. Refer to Wiring Repairs . Did you complete the repair? | Go to Step 20 | -- |
13 | Repair the open in the CAN low between the TCM and the CAN splice circuit. Refer to Wiring Repairs . Did you complete the repair? | Go to Step 20 | -- |
14 | Repair the short to voltage in the CAN high circuit. Refer to Wiring Repairs . Did you complete the repair? | Go to Step 20 | -- |
15 | Repair the short to ground in the CAN high circuit. Refer to Wiring Repairs . Did you complete the repair? | Go to Step 20 | -- |
16 | Repair the short across the CAN high and CAN low circuits. Refer to Wiring Repairs . Did you complete the repair? | Go to Step 20 | -- |
17 | Repair the short to ground in the CAN low circuit. Refer to Wiring Repairs . Did you complete the repair? | Go to Step 20 | -- |
18 | Repair the short to voltage in the CAN low circuit. Refer to Wiring Repairs . Did you complete the repair? | Go to Step 20 | -- |
19 | Replace the TCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | Go to Step 20 | -- |
20 |
Does the DTC run and pass? | Go to Step 21 | Go to Step 2 |
21 | Does the scan tool display any DTCs that you have not diagnosed? | System OK | |
