GM Service Manual Online
For 1990-2009 cars only

The following are the 2 primary components of vibration diagnosis:

    • The physical properties of objects
    • The object's properties of conducting mechanical energy

The repetitive up/down or back/forth movement of a component causes most customer vibration complaints. The following are the common components that vibrate:

    • The steering wheel
    • The seat cushion
    • The frame
    • The instrument panel

Vibration diagnosis involves the following steps:

  1. Measure the repetitive motion and assign a value to the measurement in cycles per second or cycles per minute.
  2. Relate the frequency to the rotational speed of a component that is operating at the same rate or speed.
  3. Inspect and test the components for conditions that cause vibration.

For example, performing the following steps will help demonstrate the vibration theory:


    Object Number: 95587  Size: SH
  1. Clamp a yardstick to the edge of a table, leaving approximately 50 cm (20 in) hanging over the edge of the table.
  2. Pull down on the edge of the stick and release while observing the movement of the stick.

The motion of the stick occurs in repetitive cycles. The cycle begins at midpoint, continues through the lowest extreme of travel, then back past the midpoint, through the upper extreme of travel, and back to the midpoint where the cycle begins again.

The cycle occurs over and over again at the same rate, or frequency. In this case, approximately 10 cycles per second. If we measure the frequency to reflect the number of complete cycles that the yardstick made in one minute, the measure would be 10 cycles x 60 seconds = 600 cycles per minute (cpm).

We have also found a specific amount of motion, or amplitude, in the total travel of the yardstick from the very top to the very bottom. Redo the experiment as follows:

  1. Reclamp the yardstick to the edge of a table, leaving approximately 25 cm (10 in) hanging over the edge of the table.
  2. Pull down on the edge of the stick and release while observing the movement of the stick.

The stick vibrates at a much faster frequency: 30 cycles per second (1,800 cycles per minute). The total travel, or amplitude, is less.

Vibration

Vibration is the repetitive motion of an object, back and forth, or up and down. The following conditions cause most vehicle vibrations:

    • A rotating component
    • The engine combustion process firing impulses

Rotating components will vibrate with excessive imbalance or runout. During vibration diagnosis, the amount of allowable imbalance or runout should be considered a tolerance and not a specification. In other words, the less imbalance or runout, the better.

A vibration concern will occur when the firing impulses of the engine are not properly isolated from the passenger compartment.

A vibrating component operates at a consistent rate (km/h, mph, or RPM). Measure the rate of vibration in question. When the rate/speed is determined, relate the vibration to a component that operates at an equal rate/speed in order to pinpoint the source. Vibrations also tend to transmit through the body structure to other components. Therefore, just because the seat vibrates doesn't mean the source of the vibration is in the seat.

Vibrations consist of the following three elements:

    • The source -- the cause of the vibration
    • The transfer path -- the path on which the vibration travels through the vehicle
    • The responder -- the component where the vibration is felt

Object Number: 95585  Size: SH

In the preceding figure, the source of the vibration is the unbalanced tire. The transfer path is the route the vibrations travels through the vehicle's suspension system into the steering column. The responder is the steering wheel, which the customer reports as vibrating. Eliminating any one of these three elements will usually correct the condition. From the gathered information, decide which element makes the most sense to repair. Adding a brace to the steering column may keep the steering wheel from vibrating, but adding a brace is not a practical solution. The most direct and effective repair would be to properly balance the tire.


Object Number: 95586  Size: SH

Vibration can also produce noise. As an example, consider a vehicle that has an exhaust pipe which is grounded to the frame. The source of the vibration is the engine firing impulses traveling through the exhaust. The transfer path is a grounded or bound-up exhaust hanger. The responder is the frame. The floor panel vibrates, acting as a large speaker, which produces noise. The best repair would be to align the exhaust system and correct the grounded condition at the frame. This would eliminate the transfer path.

Cycle


Object Number: 95588  Size: SF
(1)1st Cycle
(2)2nd Cycle
(3)3rd Cycle
(4)Time

Vibration Cycles in Powertrain Components


Object Number: 95589  Size: SH
(1)Spindle
(2)Pinion Nose

The word cycle comes from the same root as the word circle: both begin and end at the same point. All vibrations consist of repetitive cycles.

Frequency


Object Number: 95590  Size: MF
(1)Amplitude
(2)Reference
(3)Time in Seconds
(4)1 Second

Frequency is defined as the rate at which an event occurs during a given period of time. With a vibration, the event is a cycle, and the period of time is one second. Thus, frequency is expressed in cycles per second, or Hertz (Hz). Multiply the Hertz by 60 to get the cycles, or revolutions per minute (RPM).

Amplitude


Object Number: 95593  Size: SH
(1)Maximum
(2)Minimum
(3)Zero-to-Peak Amplitude
(4)Peak-to-Peak Amplitude

Amplitude is the maximum value of a periodically varying quantity. Used in vibration diagnostics, amplitude is the magnitude of the disturbance. A severe disturbance would have a high amplitude and a minor disturbance would have a low amplitude.

Amplitude is measured by the amount of actual movement, or the displacement. For example, consider the vibration caused by an out-of-balance wheel at 80 km/h (50 mph) as opposed to 40 km/h (25 mph). As the speed increases, the amplitude increases.

Free Vibration

Free vibration is the continued vibration in the absence of any outside force. In the yardstick example, the yardstick continued to vibrate even after the end was released.

Forced Vibration

Forced vibration is when an object is vibrating continuously as a result of an outside force.

Centrifugal Force Due to an Imbalance


Object Number: 95594  Size: MF
(1)Location of Imbalance (Degrees)
(2)Centrifugal Force Acting on Spindle

A spinning object with an imbalance generates a centrifugal force. Performing the following steps will help to demonstrate centrifugal force:

  1. Tie a nut to a string.
  2. Hold the string. The nut hangs vertically due to gravity.
  3. Spin the string. The nut will spin in a circle.

Centrifugal force is trying to make the nut fly outward, causing the pull you feel on your hand. An unbalanced tire follows the same example. The nut represents the imbalance in the tire. The string represents the tire/wheel/suspension assembly. As the vehicle speed increases, you can feel the disturbing force of the unbalanced tire in the steering wheel, the seat, and the floor. This disturbance will be repetitive (Hz) and the amplitude will increase. At higher speeds, both the frequency and the amplitude will increase. As the tire revolves, the imbalance, or the centrifugal force, will alternately lift the tire up and force the tire downward, along with the spindle, once for each revolution of the tire.

Natural or Resonant Frequency


Object Number: 95595  Size: SH

The natural frequency is the frequency at which an object tends to vibrate. Bells, guitar strings, and tuning forks are all examples of objects that tend to vibrate at specific frequencies when excited by an external force.

Suspension systems, and even engines within their mounts, have a tendency to vibrate at certain frequencies. This is why some vibration complaints occur only at specific vehicle speeds or engine RPM.

The stiffness and the natural frequency of a material have a relationship. Generally, the stiffer the material, the higher the natural frequency. The opposite is also true. The softer a material, the lower its natural frequency. Conversely, the greater the mass, the higher the natural frequency.

Resonance


Object Number: 95596  Size: SH
(1)Frequency - cps
(2)Suspension Frequency
(3)Unbalanced Excitation
(4)Point of Resonance
(5)Problem Speed

All objects have natural frequencies. The natural frequency of a typical automotive front suspension is in the 10-15 Hz range. This natural frequency is the result of the suspension design. The suspension's natural frequency is the same at all vehicle speeds. As the tire speed increases along with the vehicle speed, the disturbance created by the tire increases in frequency. Eventually, the frequency of the unbalanced tire will intersect with the natural frequency of the suspension. This causes the suspension to vibrate. The intersecting point is called the resonance.

The amplitude of a vibration will be greatest at the point of resonance. While you may feel the vibration above and below the problem speed, you will feel the vibration the most at the point of resonance.

Damping


Object Number: 95597  Size: MF
(1)Low Damping
(2)High Damping

Damping is the ability of an object or material to dissipate or absorb vibration. The automotive shock absorber is a good example. The function of the shock absorber is to absorb or dampen the oscillations of the suspension system.

Beating (Phasing)


Object Number: 95599  Size: MF

Two separate disturbances that are relatively close together in frequency will lead to a condition called beating, or phasing. Beating occurs when two vibrating forces are adding to, or subtracting from, each other's amplitude. A beating vibration condition will increase in intensity or amplitude in a repetitive fashion as the vehicle travels at a steady speed. This beating vibration can produce the familiar droning noise heard in some vehicles. In many cases, eliminating either one of the disturbances can correct the condition.

Order

Order refers to how many times an event occurs during one revolution of a rotating component.


Object Number: 386785  Size: SF

For example, a tire with one high spot would create a disturbance once for every revolution of the tire. This is called first-order vibration.


Object Number: 386788  Size: SF

An oval-shaped tire with two high spots would create a disturbance twice for every revolution. This is called second-order vibration. Three high spots would be third-order, and so forth. Two first-order vibrations may add or subtract from the overall amplitude of the disturbance, but that is all. Two first-order vibrations do not equal a second-order vibration. Due to centrifugal force, an unbalanced component will always create a first-order vibration, at minimum.