GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Isuzu 🢒 2004 🢒 Isuzu - N Series 🢒 Engine 🢒 Engine Controls - 4.8L, 5.3L, and 6.0L 🢒 DTC P0455

System Description

The control module tests the evaporative emission (EVAP) system for a large leak. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the EVAP system vacuum level. When the conditions for running are met, the control module commands the EVAP canister purge solenoid valve open and the EVAP canister vent solenoid valve closed . This allows engine vacuum to enter the EVAP system. At a calibrated time, or vacuum level, the control module commands the EVAP canister purge solenoid valve closed, sealing the system, and monitors the FTP sensor input in order to determine the EVAP system vacuum level. If the system is unable to achieve the calibrated vacuum level, or the vacuum level decreases too rapidly, this DTC sets.

The following table illustrates the relationship between the ON and OFF states, and the OPEN or CLOSED states of the EVAP canister purge and vent solenoid valves.

Control Module Command

EVAP Canister Purge Solenoid Valve

EVAP Canister Vent Solenoid Valve

ON

Open

Closed

OFF

Closed

Open

Conditions for Running the DTC
    • DTC P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0125, P0131, P0132, P0133, P0134, P0135, P0136, P0137, P0138, P0140, P0141, P0151, P0152, P0153, P0154, P0155, P0156, P0157, P0158, P0160, P0161, P0220, P0442, P0443, P0449, P0452, P0453, P1111, P1112, P1114, P1115, P1125, P2135 are not set.
    • The engine is running.
    • The ignition voltage is between 10-18 volts.
    • The barometric pressure (BARO) is more than 75 kPa.
    • The fuel level is between 15-85 percent.
    • The engine coolant temperature (ECT) is between 4-65°C (39-149°F).
    • The intake air temperature (IAT) is between 4-75°C (39-167°F).
    • The start-up ECT and IAT are within 9°C (16°F) of each other.

Conditions For Setting the DTC

The EVAP system is not able to achieve or maintain vacuum during the diagnostic test.

Action Taken When the DTC Sets
    • The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC
    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Diagnostic Aids
    • To help locate intermittent leaks, use the J 41413-200 Evaporative Emissions System Tester (EEST) to introduce smoke into the EVAP system. Move all EVAP components while observing smoke with the J 41413-SPT High Intensity White Light. Introducing smoke in 15   second intervals will allow less pressure into the EVAP system. When the system is less pressurized, the smoke will sometimes escape in a more condensed manner.
    • A temporary blockage in the EVAP canister purge solenoid valve, purge pipe or EVAP canister could cause an intermittent condition. Inspect and repair any restriction in the EVAP system.
    • To improve the visibility of the smoke exiting the EVAP system, observe the suspected leak area from different angles with the J 41413-SPT .
    • Reviewing the Failure Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.
    • For intermittent conditions, refer to Intermittent Conditions .

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. Introducing smoke in 15 second intervals may allow smaller leak areas to be more noticeable. When the system is less pressurized, the smoke will sometimes escape in a more condensed manner.

  2. This step verifies proper operation of the fuel tank pressure (FTP) sensor.

    3.

  3. A normal operating FTP sensor should increase above 5 inches of H2O and stop between 6 inches of H2O and 7 inches of H2O.

Step

Action

Values

Yes

No

Schematic Reference: Emission Hose Routing Diagram

1

Did you perform the Diagnostic System Check-Engine Controls?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2
  1. Inspect the evaporative emission (EVAP) system for the following conditions:
    2. • Loose, missing, or damaged service port schrader valve
    • Loose, incorrect, missing, or damaged fuel fill cap
    • A damaged EVAP canister purge solenoid valve
  2. Raise the vehicle on a hoist.
  3. Inspect the EVAP system for the following conditions:
    4. • Disconnected, improperly routed, kinked, or damaged EVAP pipes and hoses
    • A damaged EVAP canister vent solenoid valve or EVAP canister

Did you find and correct the condition?

--

Go to Step 16

Go to Step 3

3

Important: Ensure that the vehicle underbody temperature is similar to the ambient temperature and allow the surrounding air to stabilize before starting the diagnostic procedure. System flow will be less with higher temperatures.

  1. Turn OFF the ignition.
  2. Connect the J 41413-200 Evaporative Emissions System Tester (EEST) power supply clips to a known good 12-volt source.
  3. Install the J 41415-40 Fuel Tank Cap Adapter to the fuel fill pipe.
  4. Connect the J 41413-200 nitrogen/smoke supply hose to the J 41415-40 .
  5. Turn ON the ignition, with the engine OFF.
  6. Command the EVAP canister vent solenoid valve closed with a scan tool.
  7. Turn the nitrogen/smoke valve on the J 41413-200 control panel to SMOKE.
  8. Use the remote switch to introduce smoke into the EVAP system.
  9. Use the J 41413-VLV EVAP Service Port Vent Fitting to open the EVAP service port.
  10. Remove the J 41413-VLV once smoke is observed.
  11. Continue to introduce smoke into the EVAP system for an additional 60 seconds.
  12. Inspect the entire EVAP system for exiting smoke with the J 41413-SPT High Intensity White Light.
  13. Continue to introduce smoke at 15 second intervals until the leak source has been located.

Did you locate and repair a leak source?

--

Go to Step 16

Go to Step 4

4
  1. Disconnect the J 41415-40 from the fuel fill pipe.
  2. Install the fuel fill cap to the fuel fill pipe.
  3. Connect the J 41413-200 nitrogen/smoke supply hose to the EVAP service port.
  4. Use the remote switch to introduce smoke into the EVAP system.
  5. Inspect the entire EVAP system for exiting smoke with the J 41413-SPT .
  6. Continue to introduce smoke at 15 second intervals until the leak source has been located.

Did you locate and repair a leak source?

--

Go to Step 16

Go to Step 5

5

  1. Use the remote switch to stop introducing smoke.
  2. Install the J 41415-40 to the fuel fill pipe.
  3. Connect the J 41413-200 nitrogen/smoke supply hose and vehicle fuel fill cap to the J 41415-40
  4. Command the EVAP canister vent solenoid valve open with a scan tool.
  5. Compare the fuel tank pressure sensor parameter with a scan tool to theJ 41413-200 pressure/vacuum gage.

Is the scan tool fuel tank pressure sensor parameter within the specified value of the J 41413-200 pressure/vacuum gage?

1 in H2O

Go to Step 6

Go to Step 12

6

  1. Seal the EVAP system using the EVAP Purge/Seal function with a scan tool.
  2. Turn the nitrogen/smoke valve on the J 41413-200 control panel to NITROGEN.
  3. Use the J 41413-200 to pressurize the EVAP system to the first specified value.

Is the fuel tank pressure sensor parameter more than the second specified value?

13 in H2O

5 in H2O

Go to Step 7

Go to Step 12

7
  1. Stop introducing nitrogen into the EVAP system with the remote switch.
  2. Increase the EVAP canister purge solenoid valve to 100 percent.

Is the fuel tank pressure sensor parameter less than the specified value?

1 in H2O

Go to Diagnostic Aids

Go to Step 8

8

Disconnect the EVAP purge pipe from the EVAP canister purge solenoid valve.

Is the fuel tank pressure sensor parameter less than the specified value?

1 in H2O

Go to Step 13

Go to Step 9

9

Disconnect the EVAP purge pipe at the EVAP canister.

Is the fuel tank pressure sensor parameter less than the specified value?

1 in H2O

Go to Step 14

Go to Step 10

10

Disconnect the EVAP vapor pipe at the EVAP canister.

Is the fuel tank pressure sensor parameter less than the specified value?

1 in H2O

Go to Step 15

Go to Step 11

11

Repair the pinched or obstructed EVAP vapor pipe.

Did you complete the repair?

--

Go to Step 16

--

12

Replace the FTP sensor. Refer to Fuel Tank Pressure Sensor Replacement .

Did you complete the replacement?

--

Go to Step 16

--

13

Replace the EVAP canister purge solenoid valve. Refer to Evaporative Emission Canister Purge Solenoid Valve Replacement .

Did you complete the replacement?

--

Go to Step 16

--

14

Repair the restriction in the EVAP purge pipe. Refer to Evaporative Emission System Hoses/Pipes Replacement .

Did you complete the repair?

--

Go to Step 16

--

15

Replace the EVAP canister. Refer to Evaporative Emission Canister Replacement .

Did you complete the replacement?

--

Go to Step 16

--

16

Important: DO NOT exceed the specified value in this step. Exceeding the specified value may produce incorrect test results.

  1. Connect the J 41413-200 to the fuel fill pipe.
  2. Turn the nitrogen/smoke valve to NITROGEN.
  3. Seal the EVAP system using the EVAP Purge/Seal function with a scan tool.
  4. Pressurize the EVAP system to the specified value.
  5. Observe the J 41413-200 pressure/vacuum gage for 5 minutes.

Does the J 41413-200 pressure/vacuum gage remain constant?

5 in H2O

Go to Step 17

Go to Step 3

17

Observe the fuel tank pressure sensor parameter with a scan tool.

Is the scan tool fuel tank pressure parameter within the specified value of the J 41413-200 pressure/vacuum gage?

1 in H2O

Go to Step 18

Go to Step 5

18
  1. Observe the J 41413-200 pressure/vacuum gage.
  2. Increase the EVAP canister purge solenoid valve to 100 percent.

Does the pressure decrease?

--

Go to Step 19

Go to Step 8

19

Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List

System OK