GM Service Manual Online
For 1990-2009 cars only

Inspections

Action

DEFINITION: Fuel economy, as measured by an actual road test, is noticeably lower than expected. Also, fuel economy is noticeably lower than the economy was on this vehicle at one time, as previously shown by an actual road test.

Preliminary

    • Refer to Important Preliminary Inspections Before Starting in Symptoms - Engine Controls .
    • Search for bulletins.
    • Verify that the powertrain control module (PCM) grounds are clean, tight, and in the proper locations.
    • Inspect the owners driving habits.
       - Is the A/C ON or the Defroster mode ON full time?
       - Are the tires at the correct pressure?
       - Are there excessively heavy loads being carried?
       - Is the acceleration rate too much, too often?
       - Remove the air filter element and inspect for dirt or for restrictions. Refer to Air Cleaner Element Replacement . Replace as necessary.

Fuel System

    • Inspect the type, quality, and alcohol content of the fuel. Oxygenated fuels have lower energy and may deliver reduced fuel economy. Refer to Alcohol/Contaminants-in-Fuel Diagnosis .
    • Inspect the fuel injectors. Refer to Fuel Injector Solenoid Coil Test .
    • Inspect for incorrect fuel pressure. Refer to Fuel System Diagnosis .
    • Inspect for a restricted fuel filter. Refer to Fuel System Diagnosis .
    • Inspect for a contaminated fuel condition. Refer to Alcohol/Contaminants-in-Fuel Diagnosis .
    • Inspect that each fuel injector harness is connected to the correct injector and cylinder. Relocate the injector harnesses as necessary.
    • Inspect for foreign material accumulation in the throttle bore, coking on the throttle valve, or on the throttle shaft.
    • Inspect for the following that may cause the engine to run rich:

Notice: Refer to Heated Oxygen and Oxygen Sensor Notice in the Preface section.

       - Water intrusion in the HO2S connector
       - Engine oil contaminated by fuel
       - An EVAP canister purge condition
       - Incorrect fuel pressure--Refer to Fuel System Diagnosis .
       - A leaking fuel pressure regulator--Refer to Fuel System Diagnosis .
       - Leaking fuel injectors--Refer to Fuel System Diagnosis .
       - An inaccurate mass air flow (MAF) sensor
       - Blockage on the inlet screen of the MAF sensor--Refer to Manifold Absolute Pressure Sensor Replacement .
       - Vacuum hoses that are split, kinked, or improperly connected
       - An air intake duct that is collapsed or restricted--Refer Air Cleaner Resonator Outlet Duct Replacement .
       - An air filter that is dirty or restricted--Refer to Air Cleaner Element Replacement .

Sensor/System

    • Inspect the air intake system and crankcase for air leaks.
    • Inspect the crankcase ventilation valve for proper operation. Place a finger over the inlet hole in the valve end several times. The valve should snap back. If not, replace the valve.
    • Inspect for an inaccurate speedometer.
    • Use a scan tool in order to monitor the knock sensor (KS) system for excessive spark retard activity. Refer to Knock Sensor (KS) System Description .

Ignition System

    • Inspect for proper ignition voltage output with the J 26792 Spark Tester .
    • Remove the spark plugs and inspect for the following:
       - Wet plugs
       - Cracks
       - Wear
       - Improper gap
       - Burned electrodes
       - Heavy deposits

Refer to Spark Plug Inspection .

    • An improper spark plug gap will cause a driveability problem. Refer to Spark Plug Inspection . Gap the spark plugs using a wire gauge gap tool Refer to Spark Plug Replacement .
    • Determine the cause of the fouling before replacing the spark plugs. Refer tp Spark Plug Inspection .
    • Visually and physically inspect the secondary ignition for the following:
       - Ignition wires arcing to ground
       - Ignition wires for proper routing
    • Soaking the secondary ignition system with water from a spray bottle may help locate damaged or deteriorated components. Look and listen for arcing or misfiring as you apply water.
    • Inspect for loose ignition coil grounds. Refer to Electronic Ignition (EI) System Diagnosis .

Engine Cooling System

    • Inspect the engine coolant level for being low.
    • Inspect the engine thermostat for proper operation and for the correct heat range.

Engine Mechanical

    • Inspect engine mechanical for the following:
       - Compression--Refer to Engine Compression Test in Engine Mechanical.
       - Sticking or leaking valves
       - Worn camshaft lobes
       - Valve timing
       - Bent push rods
       - Worn rocker arms
       - Broken valve springs
       - Excessive oil in combustion chamber--Leaking valve seals. Refer to Oil Consumption Diagnosis in Engine Mechanical.
    • For incorrect basic engine parts inspect for the following:
       - The camshaft--Refer to Camshaft and Bearings Cleaning and Inspection in Engine Mechanical.
       - The cylinder heads--Refer to Cylinder Head Cleaning and Inspection in Engine Mechanical.
       - The pistons, etc.--Refer to Piston, Connecting Rod, and Bearing Cleaning and Inspection in Engine Mechanical.

Refer to Symptoms - Engine Mechanical in Engine Mechanical for diagnostic procedures.

Additional Inspections

    • Visually and physically check the vacuum hoses for splits, kinks, and proper connections and routing as shown on Vehicle Emission Control Information label.
    • Inspect the transmission torque converter clutch (TCC) operation. The scan tool should indicate a RPM drop, when the system commands the TCC ON.
    • Inspect the exhaust system for a possible restriction. Inspect for the following:
       - Inspect the exhaust system for damaged or collapsed pipes.
       - Inspect the mufflers for heat distress or possible internal failure.
       - Inspect for possible plugged three-way catalytic converters by comparing the exhaust system back pressure on each side of the engine. Inspect the back pressure by removing the secondary air injection (AIR) check valves near the exhaust manifolds.
    • Electromagnetic interference (EMI) on the reference circuit can cause an engine miss condition. A scan tool can usually detect EMI by monitoring the engine RPM. A sudden increase in RPM with little change in actual engine RPM change indicates EMI is present. Inspect for high voltage components, near ignition control circuits, if a condition exists.
    • Inspect the park neutral position (PNP) switch circuit.
    • Inspect the intake and the exhaust manifold passages for casting flash.
    • Inspect the brake system for dragging or improper operation. Verify that the vehicle operator does not drive with a foot on the brake pedal.