Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC P1400: Cold Start Emission Reduction Control SystemCircuit/System Description
The catalytic converter must be warmed to efficiently reduce the emissions. The cold start strategy is to reduce the amount of time it takes to warm the catalytic converter. During a cold start, the engine idle speed is elevated and spark timing is retarded to allow the catalyst to warm quickly. This diagnostic monitors the following to build an exhaust energy model:
| • | Engine speed |
| • | Spark advance |
| • | Throttle position |
| • | Engine airflow |
| • | Engine coolant temperature |
| • | Engine runtime |
| • | Park/Neutral position |
| • | Vehicle speed |
The actual model is then compared to the expected exhaust energy model.
Conditions for Running the DTC
| • | The engine is running, and a cold start has been detected. |
| • | Vehicle speed is less than 2 km/h (1 mph). |
| • | The engine is at idle with no input from the accelerator pedal. |
| • | DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0201, P0202, P0203, P0204, P0205, P0206, P0300, P0335, P0336, P0351, P0352, P0353, P0501, P0502, P0506, P0507, P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, P0641, P0651, P1101, P1516, P1682, P2101, P2119, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, P2176, P2610 are not set. |
This DTC runs for 15 seconds within the first 2 minutes of start-up. This diagnostic runs once per trip when a cold start has been determined.
Conditions for Setting the DTC
The actual exhaust energy model does not match the expected exhaust energy model.
Action Taken When the DTC Sets
DTC P1400 is a Type A DTC.
Conditions for Clearing the MIL/DTC
DTC P1400 is a Type A DTC.
Reference Information
Description and Operation
Engine Control Module Description
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Diagnostic Aids
Any loading of the engine that lowers engine RPM, such as with partial application of the clutch, A/C cycling etc., during the first 120 seconds of engine runtime may set this DTC.
Circuit/System Verification
- Allow the engine to cool.
- Start and idle the engine for at least 2 minutes.
- DTC P1400 should run and pass.
Circuit/System Testing
| • | Inspect the air intake system for the following: |
| - | Damage, restriction, or modification |
| - | Dirty or deteriorating air filter element |
| - | Crankcase ventilation system for correct operation |
| - | Water intrusion |
| - | Vacuum leak and other un-metered air downstream of the mass air flow (MAF) sensor |
| - | Intake manifold leak |
| • | Inspect the exhaust system for the following: |
| - | Water intrusion |
| - | Exhaust leak |
| - | Damaged, restricted, modified or enhanced exhaust system |
| • | Inspect the engine mechanical for items that could alter the air flow into the combustion chamber. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
