Diagnostic Instructions

DTC Descriptors

DTC P0117: Engine Coolant Temperature (ECT) Sensor Circuit Low Voltage

DTC P0118: Engine Coolant Temperature (ECT) Sensor Circuit High Voltage

Diagnostic Fault Information

Circuit	Short to Ground	High Resistance	Open	Short to Voltage	Signal Performance
ECT Sensor Signal	P0117	P0118	P0118	P0118*	P0116, P0125, P0128
Low Reference	--	P0118	P0118	P0118*	P0125, P0128
*ECM or sensor damage may occur if the circuit is shorted to B+

Typical Scan Tool Data

ECT Sensor Temperature

Circuit	Short to Ground	Open	Short to Voltage
Operating Conditions: Engine operating in Closed Loop Parameter Normal Range: Varies with coolant temperature
ECT Sensor Signal	150°C (302°F)	-40°C (-40°F)	-40°C (-40°F)
Low Reference	--	-40°C (-40°F)	-40°C (-40°F)

Circuit/System Description

The engine coolant temperature (ECT) sensor is a variable resistor that measures the temperature of the engine coolant. The engine control module (ECM) supplies 5 volts to the ECT signal circuit and supplies a ground to the low reference circuit.

Conditions for Running the DTC

P0117

P0118

Conditions for Setting the DTC

P0117

The ECM detects that the ECT is more than 149°C (300°F) for more than 5 seconds.

P0118

The ECM detects that the ECT is less than -39°C (-38°F) for more than 5 seconds.

Action Taken When the DTC Sets

DTCs P0117 and P0118 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0117 and P0118 are Type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

Warning: Under pressure, the temperature of the solution in the radiator can be considerably higher, without boiling. Removing the radiator cap while the engine is hot (pressure is high), will cause the solution to boil instantaneously, with explosive force. The solution will spew out over the engine, fenders, and the person removing the cap. Serious bodily injury may result. Flammable antifreeze, such as alcohol, is not recommended for use at any time. Flammable antifreeze could cause a serious fire.

1. Turn OFF the ignition.
2. Inspect the cooling system surge tank for the proper engine coolant level.
3. Turn ON the ignition, with the engine OFF.
4. Use the scan tool to verify the proper operation of the engine cooling system fans.
5. Turn OFF the ignition.
6. Verify the proper heat range, and the operation of the thermostat.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the ECT sensor.
2. Ignition OFF for 90 seconds, test for less than 5 ohms of resistance between the low reference circuit terminal A and ground.

⇒	If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

3. Ignition ON, verify the scan tool ECT parameter is colder than -39°C (-38°F).

⇒	If greater than the specified range, test the signal circuit terminal B for a short to ground. If the circuit tests normal, replace the ECM.

4. Install a 3A fused jumper wire between the signal circuit terminal B and the low reference circuit terminal A. Verify the scan tool ECT parameter is greater than 149°C (300°F).

⇒	If less than the specified range, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM.

5. If all circuits test normal, test or replace the ECT sensor.

Component Testing

Measure and record the resistance of the ECT sensor at various ambient temperatures, then compare those measurements to the Temperature vs Resistance table. Refer to Temperature Versus Resistance.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.