System Description
This system includes the Distributor, the CAM position sensor ignition coil with the ignition coil driver, the secondary wires, spark plugs, the (KS) sensors and the crank sensors. The ignition system is controlled by the Vehicle Control Module (VCM). The VCM monitors the information from various engine sensors, computes the desired spark timing and controls the dwell and firing of the ignition coil via an (IC) line to the coil driver.
Diagnostic Aids
Check the following when the distributor rotor does not rotate, while engine is cranking:
| • | A broken distributor drive shaft |
| • | A worn distributor drive gear or camshaft timing chain and gears |
An intermittent may be caused by any of the following conditions:
| • | A poor connection |
| • | Rubbed through wire insulation |
| • | A broken wire inside the insulation |
Thoroughly check any circuitry that is suspected of causing the intermittent complaint. Refer to Intermittents and Poor Connections Diagnosis in Wiring Systems.
If a repair is necessary, refer to Wiring Repairs or Connector Repairs in Wiring Systems.
Test Description
The numbers below refer to the step numbers in the diagnostic table.
The battery should be fully charged prior to any tests.
-
Checks for proper output from the enhanced ignition system. The spark test requires a minimum of 25,000 volts to operate. This check can be used in case of an ignition miss because the system may provide enough voltage to run the engine but not enough to operate a spark plug under heavy load.
-
This test separates the distributor cap, rotor, and ignition wires from the ignition coil in order to help identify a secondary ignition system problem.
-
This test checks the ignition control module, connections, and wiring.
-
This test begins to determine if the VCM is providing a signal to the ignition control module. If the VCM is not providing a signal to the ignition control module, the problem exists between the ignition control module and the VCM.
-
This test checks for a basic engine mechanical problem.
Step | Action | Value(s) | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 |
Important:: Before clearing the DTCs, use the scan tool Capture Info function to save the Freeze Frame and Failure Records for reference. The control module's data is deleted once the Clear Info function is used. Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? | -- | ||||||||||
Is adequate spark present? | -- | Go to Symptoms | ||||||||||
Is adequate spark present? | ||||||||||||
4 | Measure the coil wire resistance using a DMM. The resistance should be approximately the specified value. Is the resistance near the specified value? | 1000 ohms/inch | ||||||||||
Does the test lamp flash while cranking the engine? | -- | |||||||||||
6 |
Does the test lamp illuminate? | -- | ||||||||||
7 |
Is the voltage more than the specified value? | 10.0 V | ||||||||||
8 |
Is the circuit open? | -- | ||||||||||
9 |
Is the voltage above the specified value? | 10.0 V | ||||||||||
10 | Probe the ignition control module harness connector terminal C with a test lamp connected to B+. Does the test lamp illuminate? | -- | ||||||||||
Is the voltage within the specified range? | 1.0-4.0 V | |||||||||||
12 |
Are any of these conditions present? | -- | ||||||||||
Did the distributor rotor turn? | -- | Go to Symptoms | ||||||||||
14 |
Is the circuit open? | -- | ||||||||||
15 | Probe the ignition control (IC) circuit at the VCM C3 harness connector with a test lamp connected to B+. Does the test lamp illuminate? | -- | ||||||||||
16 |
Does the test lamp illuminate? | -- | ||||||||||
17 |
Is the action complete? | -- | -- | |||||||||
18 |
Is the action complete? | -- | -- | |||||||||
19 | Check for a poor ignition control module connection. Did you find a problem? | -- | ||||||||||
20 | Check for a poor coil connection . Did you find a problem? | -- | ||||||||||
21 | Check for a poor VCM connection. Did you find a problem? | -- | ||||||||||
22 | Repair the open ignition control module ground circuit. Refer to Wiring Repairs in Wiring Systems. Is the action complete? | -- | -- | |||||||||
23 | Repair the open IC circuit between the VCM and the ignition control module. Refer to Wiring Repairs in Wiring Systems. Is the action complete? | -- | -- | |||||||||
24 | Repair the grounded IC circuit between the VCM and the ignition control module. Refer to Wiring Repairs in Wiring Systems. Is the action complete? | -- | -- | |||||||||
25 | Repair the short to voltage in the IC circuit between the VCM and the ignition control module. Refer to Wiring Repairs in Wiring System. Is the action complete? | -- | -- | |||||||||
26 | Repair the open in the tachometer signal circuit between the ignition coil and the ignition control module. Refer to Wiring Repairs in Wiring System. Is the action complete? | -- | -- | |||||||||
27 | Repair the short to ground in the tachometer signal circuit between the ignition coil and the ignition control module. Refer to Wiring Repairs in Wiring Systems. Is the action complete? | -- | -- | |||||||||
28 | Repair the circuit as necessary. Refer to Wiring Repairs in Wiring Systems. Is the action complete? | -- | -- | |||||||||
29 | Replace the ignition coil. Refer to Ignition Coil and Ignition Coil Module Replacement in Engine Electrical. Is the action complete? | -- | -- | |||||||||
30 | Replace the coil wire. Refer to Ignition Coil and Ignition Coil Module Replacement in Engine Electrical. Is the action complete? | -- | -- | |||||||||
31 | Replace the distributor rotor. Refer to Distributor Overhaul . Is the action complete? | -- | -- | |||||||||
32 | Replace the distributor cap. Refer to Distributor Overhaul . Is the action complete? | -- | -- | |||||||||
33 | Replace the ignition control module. Refer to Ignition Coil and Ignition Coil Module Replacement in Engine Electrical. Is the action complete? | -- | -- | |||||||||
34 |
Program the new VCM. Refer to VCM Replacement/Programming . Is the action complete? | -- | -- | |||||||||
35 | Operate the vehicle within the conditions under which the original symptom was noted. Does the system operate properly? | -- | System OK |
