Circuit Description
The manifold absolute pressure (MAP) sensor is a pressure sensor. The control module supplies the MAP sensor a reference voltage, signal, and ground circuits. When manifold vacuum is low, the MAP sensor signal voltage rises to a value near the reference voltage, and the MAP sensor signal voltage decreases when the manifold vacuum increases. The control module monitors the MAP sensor signal circuit voltage in order to calculate the vacuum within the intake manifold.
Certain vehicle models will also use the MAP sensor in order to calculate the barometric pressure (BARO) when the ignition switch is turned ON and the engine is NOT cranked. This BARO reading may also be updated whenever the engine is operated at wide open throttle (WOT).
This DTC determines if the MAP sensor signal input to the VCM does not closely match what the predicted value for the MAP sensor should be. The VCM calculates what the MAP signal voltage should be, based on engine RPM. If the MAP sensor voltage and the predicted MAP sensor values do not closely match, this DTC will be set.
Conditions for Running the DTC
| • | No active TP sensor DTCs |
| • | No active EGR DTCs |
| • | Any variation in engine speed is less than 75 RPM |
| • | Any variation in throttle position is less than 1.5 percent |
| • | Any variation in idle air is less than 4 steps |
| • | The change in EGR flow rate is less than 2 percent |
| • | No change in brake switch status |
| • | No change in the clutch status (manual transmission) |
| • | No change in AC clutch status for 2 seconds |
| • | The engine speed is between 400-5000 RPM |
Conditions for Setting the DTC
The MAP voltage is outside acceptable limits for more than 24 seconds.
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) if a failure is detected during 2 consecutive key cycles. |
| • | The control module sets the DTC and records the operating conditions at the time the diagnostic failed. The failure information is stored in the scan tool Freeze Frame/Failure Records. |
Conditions for Clearing the MIL or DTC
| • | The control module turns OFF the MIL after 3 consecutive drive trips when the test has run and passed. |
| • | A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles. A warm-up cycle occurs when the coolant temperature has risen 22°C (40°F) from the startup coolant temperature and the engine coolant reaches a temperature that is more than 70°C (158°F) during the same ignition cycle. |
| • | Use a scan tool in order to clear the DTCs. |
Diagnostic Aids
Check the MAP sensor vacuum source for leaks, restrictions or poor connections.
Important: After removing the MAP sensor from the intake manifold, replace the MAP sensor to the intake manifold seal.
Remove the MAP sensor from the intake manifold and gently twist the sensor in order to check for intermittent connections. Output changes of more than 0.1 volt indicate a bad connector or connection.
An intermittent may be caused by any of the following conditions:
| • | A poor connection |
| • | Rubbed through wire insulation |
| • | A broken wire inside the insulation |
Thoroughly check any circuitry that is suspected of causing the intermittent complaint. Refer to Intermittents and Poor Connections Diagnosis in Wiring Systems.
If a repair is necessary, refer to Wiring Repairs or Connector Repairs in Wiring Systems.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step checks the MAP sensor's ability to correctly indicate barometric pressure.
In order to determine the correct MAP sensor display of barometric pressure for any elevation, perform either of the following procedures:
-
This step checks the MAP sensor's ability to correctly indicate engine vacuum.
The MAP sensor display is only active while the engine is operating.
| • | Compare the recorded MAP sensor display value to the BARO display on a known good vehicle. |
| • | Obtain the local weather service barometer reading (in Hg). Multiply the barometer reading by 3.4. The result indicates the correct BARO value in kPa for your area. |
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 |
Important: Before clearing the DTCs, use the scan tool Capture Info function to save the Freeze Frame and the Failure Records for reference. The control module's data is deleted once the Clear Info function is used. Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? | -- | ||
Important: Other DTCs may set when performing the following steps. Is the displayed value more than the specified value? | 75 kPa @ altitude 95 kPa @ sea level | |||
Important: The engine must remain operating during all steps that observe the MAP sensor display. Slightly raise the idle during testing in order to prevent engine stalling. Did you observe a skip or jump in the pressure display? | -- | |||
4 | Observe the MAP sensor display with 20 in Hg of vacuum applied to the MAP sensor. Is the displayed value less than the specified value? | 34 kPa | ||
5 |
Does the MAP sensor display return to the recorded value? | -- | Go to Diagnostic Aids | |
6 | Check the MAP sensor connections. Did you find a problem? | -- | ||
7 | Repair the connections as necessary. Refer to Connector Repairs in Wiring Systems. Is the action complete? | -- | -- | |
8 | Replace the MAP sensor. Refer to Manifold Absolute Pressure Sensor Replacement . Is the action complete? | -- | -- | |
9 |
Does the scan tool indicate that this diagnostic Passed? | -- | ||
10 | Does the scan tool display any additional undiagnosed DTCs? | -- | Go to the applicable DTC table | System OK |
