DTC P0440 Evaporative Emission (EVAP) System. Isuzu S/T Isuzu

For 1990-2009 cars only

Makes 🢒 Isuzu 🢒 2000 🢒 S/T Isuzu - 4WD 🢒 DTC 🢒 DTC P0440 Evaporative Emission (EVAP) System

Handling ESD Sensitive Parts Notice
Engine Controls Components
Engine Controls Schematics
OBD II Symbol Description Notice
VCM Connector End Views
Automatic Transmission Controls Schematics
Power Distribution Schematics
Power Distribution Schematics

Circuit Description

The evaporative system includes the following components:

•	The fuel tank

•	The EVAP vent solenoid

•	The fuel tank pressure sensor

•	The fuel pipes and hoses

•	The vapor lines

•	The fuel cap

•	The evaporative emission canister

•	The purge lines

•	The EVAP purge solenoid

The evaporative leak detection diagnostic strategy is based on applying a vacuum to the EVAP system and monitoring the vacuum decay rate. The VCM monitors the vacuum level via the fuel tank pressure sensor input. At an appropriate time, the EVAP purge solenoid and the EVAP vent solenoid turn ON, allowing the engine vacuum to draw a small vacuum on the entire evaporative emission system. If a sufficient vacuum level cannot be achieved, a large leak or an EVAP system malfunction is indicated. The following conditions can cause this problem:

•	A disconnected or malfunctioning fuel tank pressure sensor

•	A missing, malfunctioning, improperly installed, or loose fuel cap

•	A disconnected, damaged, pinched, or blocked EVAP purge line

•	A disconnected or damaged EVAP vent hose

•	A disconnected, damaged, pinched, or blocked fuel tank vapor line

•	A disconnected or malfunctioning EVAP purge solenoid

•	A disconnected or malfunctioning EVAP vent solenoid

•	An open ignition feed circuit to the EVAP vent or purge solenoid

•	A damaged EVAP canister

•	A leaking fuel sender assembly O-ring

•	A leaking fuel tank or fuel filler neck

Any of the above conditions can set DTC P0440.

Conditions for Running the DTC

•	No MAP sensor DTCs are active.

•	No TP sensor DTCs are active.

•	No VS sensor DTCs are active.

•	No O2 sensor DTCs are active.

•	No ECT sensor DTCs are active.

•	No IAT sensor DTCs are active.

•	DTC P0125 is not active.

•	The system voltage is between 10-17 volts.

•	The fuel level is between 12.5-87 percent.

•	The ECT is between 4°C and 30°C (39°F to 86°F).

•	The IAT is between 4°C and 30°C (39°F to 86°F)

•	The cold start temperature difference, the ECT minus the IAT, is less than:

1.5°C when the IAT is more than the ECT, or

8°C when the ECT is more than the IAT

•	The BARO is more than 73 kPa.

Conditions for Setting the DTC

The EVAP system is unable to generate a vacuum more than a calibrated value during a specified time.

Action Taken When the DTC Sets

•	This is a type A DTC that behaves like a B type, in which the VCM illuminates the MIL after the second key cycle.

•	The VCM stores the conditions that were present when the DTC sets as a Freeze Frame and Fail Records data.

Conditions for Clearing the MIL or DTC

•	The control module turns OFF the MIL after 3 consecutive drive trips when the test has run and passed.

•

A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles. A warm-up cycle occurs when the coolant temperature has risen 22°C (40°F) from the startup coolant temperature and the engine coolant reaches a temperature that is more than 70°C (158°F) during the same ignition cycle.

•	Use a scan tool in order to clear the DTCs.

Diagnostic Aids

Important: An accurate indication of fuel level is required for the VCM to properly pass or fail this DTC. Always diagnose the fuel level sensor DTCs before performing this DTCs diagnostic table. Always check for fuel level sensor DTCs stored in history.

Check for the following:

•	A loose, missing, damaged, incorrect, or improperly-installed fuel cap

•	Missing or damaged O-rings at the EVAP canister fuel vapor and purge line fittings

•	A cracked or punctured EVAP canister

•	A damaged or disconnected EVAP purge line, vent hose, or fuel tank vapor line

•	Incorrectly routed or damaged EVAP system purge and vapor lines

•	A faulty connection at the VCM-Inspect the harness connectors for:

-	Backed-out terminals

-	Improper mating

-	Broken locks

-	Improperly-formed or damaged terminals

-	Faulty terminal-to-wire connections

•	A damaged harness-Inspect the wiring harness to the EVAP vent solenoid, the EVAP purge solenoid, and the fuel tank pressure sensor for an intermittent, an open, or a short circuit.

•	Restricted lines-Inspect for kinks, pinches, or for a plugged EVAP purge or fuel tank vapor line.

Refer to Evaporative Emission System Cleaning before starting repairs.

Reviewing the Failure Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

Inspect the service port. Make sure that the valve core is not damaged. If the service port is suspect of leakage use the following procedure:

Disconnect the purge line from the EVAP purge solenoid valve.

Connect a hand vacuum pump to the service port by placing the hose and adaptor over the unthreaded end portion of the service port.

Apply vacuum to 5 inches Hg. If the vacuum does not hold, replace the entire purge line which contains the service port.

If the vehicle passes the Service Bay Test, then an intermittent leak or restriction had occurred. Check the fuel tank cap for a possible loose or off condition that may have caused this DTC to set.

If the Service Bay Test can not be run, proceed to Step 5. If a fault is not currently present the diagnostic table steps will return you to Step 3.

Refer to the information supplied with the EVAP pressure/purge diagnostic cart on proper setup and adjustment procedures.

With pressure applied, it may be necessary to disconnect the EVAP lines at the components in order to verify that a line or component is not restricted. A restriction would prevent a vacuum, or would prevent the Step 9 test pressure from forming in the fuel tank.

An EVAP pressure sensor that does not correctly respond to vacuum or pressure will cause this DTC to set.

The EVAP pressure sensor monitors a range from 7. inches Hg of pressure to -17.5 inches Hg of vacuum.

Step

Action

Values

Yes

Did you perform the Powertrain On-board Diagnostic (OBD) System check?

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

Check for DTCs P0442, P0446, P0452, P0453, P0461, P0462, P0463 and P1441.

Are any of the above EVAP system DTCs stored in history?

Go to applicable DTC

Go to Step 3

Inspect the EVAP system for the following conditions:

•	A loose, incorrect, defective or missing fuel tank cap.

•	Improperly routed, kinked, or damaged EVAP system purge lines.

•	A damaged EVAP system component.

•	A loose, missing, or damaged service port dust cap or schrader valve.

Repair the EVAP system if necessary.

Did you make a repair to the EVAP system?

Go to Step 25

Go to Step 4

Important: : Before proceeding with the Service Bay Test the vehicle must meet the following operating criteria:

•	Clear DTC Information

•	Battery voltage between 10.5--17.5 volts.

•	Fuel level between 15-85 percent

•	Key ON engine temperature less than 80°C (176°F)

If any of the above conditions are not met, the scan tool will display Test Aborted upon activating the Service Bay Test.

Record the data that are stored when the DTC sets, and clear the codes.
Using the scan tool, perform the Service Bay Test for the EVAP system.

Does the vehicle pass the Service Bay Test?

Go to Test Description and Diagnostic Aids

Go to Step 5

Turn OFF the ignition.
Connect a vacuum gauge set to in Hg directly to the purge connection of the EVAP purge solenoid valve.
Start and idle the engine.
Using a scan tool, command the EVAP purge solenoid valve to 100 percent purge.

Is the vacuum at or above the specified value?

12 in Hg

Go to Step 6

Go to Step 11

Turn OFF the ignition.
Disconnect the fuel tank vapor and the EVAP purge line from the EVAP vapor canister.
Plug the canister fitting for the fuel tank vapor line.
Connect a hand vacuum pump to the EVAP purge line canister fitting.
With the ignition ON, command the EVAP vent valve ON, or closed, with the scan tool.
Using the hand vacuum pump, apply vacuum up to the specified value.

Can you obtain and hold the specified value?

5 in Hg

Go to Step 9

Go to Step 7

Leave system connected as in step 6.
Disconnect the vent line at the EVAP vent valve.
Plug the vent line.
Using the hand vacuum pump, apply vacuum up to the specified value.

Can you obtain and hold the specified value?

5 in Hg

Go to Step 15

Go to Step 8

Inspect the EVAP vent line from the canister to the EVAP vent valve for leaks.
Replace the line if necessary.

Did you find and repair a problem?

Go to Step 25

Go to Step 21

Important: The following steps require the EVAP pressure and purge diagnostic station J 41413 and the ultrasonic leak detector J 41416 .

Always zero the EVAP pressure and vacuum gauges on the EVAP pressure and purge diagnostic station before proceeding with the diagnosis.

Turn OFF the ignition.
Remove the plug and the hand vacuum pump.
Reconnect the EVAP vapor canister purge and tank vent lines.
Connect the EVAP pressure/purge diagnostic station J 41413 to the EVAP system service port.
Using a scan tool command the EVAP vent valve closed.

Important: Do Not apply more than 15 in Hg of pressure to the EVAP system.

Continuously attempt to pressurize the EVAP system by leaving the EVAP pressure and purge diagnostic station control knob in the pressurize position.
Using the ultrasonic leak detector J 41416 , locate and repair EVAP system leak.

Did you find and repair a leak?

Go to Step 25

Go to Step 10

Check the EVAP system for restrictions. Refer to the test description.
Repair any restrictions as necessary.

Did you find and repair a restriction?

Go to Step 25

Go to Step 22

Turn ON the ignition, with the engine OFF.
Disconnect the EVAP purge solenoid valve connector.
Connect a test lamp between the purge solenoid ignition feed circuit and a known good engine ground.

Is the test lamp ON?

Go to Step 12

Go to Step 13

Connect the test lamp between the EVAP solenoid ignition feed circuit and the EVAP solenoid control circuit.
Use the scan tool to command ON the EVAP solenoid.

Is the test lamp ON?

Go to Step 19

Go to Step 14

Check for and repair the cause of no power to the EVAP purge solenoid ignition feed circuit.

Possible causes include:

An open ignition feed circuit
A shorted ignition feed circuit and open fuse
A shorted EVAP purge solenoid and open fuse
No power to the EVAP purge solenoid fuse, caused by an open maxi fuse or fuse link

Is the repair complete?

Go to Step 25

Inspect the EVAP purge solenoid control circuit for an open condition.
Repair the circuit as necessary.

Did you find and correct a problem?

Go to Step 25

Go to Step 24

Turn ON the ignition, with the engine OFF.
Disconnect the EVAP canister vent valve connector.
Connect a test lamp between the EVAP canister vent valve ignition feed circuit and ground.

Is the test lamp ON?

Go to Step 16

Go to Step 17

Connect the test lamp between the EVAP canister vent valve ignition feed circuit and the EVAP canister vent valve control circuit.
Use the scan tool to command ON the EVAP canister vent valve.

Is the test lamp ON?

Go to Step 20

Go to Step 18

Check for and repair the cause for no power to the EVAP canister vent valve ignition feed circuit.

Possible causes include:

An open ignition feed circuit
A shorted ignition feed circuit and open fuse
A shorted EVAP canister vent valve and open fuse
No power to EVAP canister vent valve fuse, caused by an open maxi fuse or fuse link

Is the repair complete?

Go to Step 25

Inspect the EVAP canister vent valve control circuit for an open condition.
Repair the circuit as necessary.

Is the repair complete?

Go to Step 25

Go to Step 24

Important: : Inspect the EVAP purge solenoid valve and the purge line for carbon contamination. Refer to Diagnostic Aids.

Replace the EVAP purge solenoid valve. Refer to Evaporative Emission Canister Purge Solenoid Valve Replacement .

Is the replacement complete?

Go to Step 25

Replace the EVAP vent valve. Refer to Evaporative Emission Vent Valve Replacement .

Is the replacement complete?

Go to Step 25

Replace the EVAP vapor canister. Refer to Evaporative Emission Canister Replacement .

Is the replacement complete?

Go to Step 25

Relieve all system pressure.
Using the scan tool, use the Purge and Seal function to turn ON the EVAP purge solenoid valve to varying vacuum levels with the engine running.
Quickly seal the system with the scan tool. Leaving the EVAP purge solenoid valve ON for higher percents or longer times will allow a higher vacuum to develop. A maximum of 8.5 in Hg of vacuum can be applied to the EVAP system using the scan tool.
While the system is sealed, compare the EVAP pressure and purge diagnostic stations vacuum gauge, set for in Hg, to the vacuum shown on the scan tool from the EVAP fuel tank pressure sensor. Allow a few seconds for the system to stabilize.

Do the values indicate the same amount of vacuum in the EVAP system to within the range specified?

2 in Hg

Go to Step 3

Go to Step 23

Replace the fuel tank pressure sensor. Refer to Fuel Tank Pressure Sensor Replacement .

Is the replacement complete?

Go to Step 25

Important: The replacement VCM must be programmed.

Replace the VCM.

Refer to VCM Replacement/Programming .

Is the action complete?

Go to Step 25

Using the scan tool, clear the DTCs.
Start the engine.
Allow the engine to idle until the engine reaches normal operating temperature.
Select DTC and the Specific DTC function.
Enter the DTC number which was set.
Operate the vehicle within the Conditions for Setting this DTC, until the scan tool indicates the diagnostic Ran.

Does the scan tool indicate the diagnostic Passed?

Go to Step 26

Does the scan tool display any additional undiagnosed DTCs?

Go to applicable DTC

System OK