GM Service Manual Online
For 1990-2009 cars only

Detonation/Spark Knock Symptom

Step

Action

Value(s)

Yes

No

Definition: A mild to severe ping, usually worse under acceleration. The engine makes sharp metallic knocks that change with throttle opening.

1

Was the Powertrain On-Board Diagnostic (OBD) System Check performed?

--

Go to Step 2

Go to Powertrain OBD System Check

2

  1. Perform a bulletin search.
  2. If a bulletin that addresses the symptom is found, correct the condition as instructed in the bulletin.

Was a bulletin found that addresses the symptom?

--

Go to Step 14

Go to Step 3

3

Was visual/physical check performed?

--

Go to Step 4

Go to Visual /Physical Check

4

If scan tool readings are normal (refer to Typical Scan Values) and there are no engine mechanical faults, fill fuel tank with a known quality gasoline that has a minimum octane reading of 87 and re-evaluate vehicle performance.

Is detonation present?

--

Go to Step 5

Go to Step 14

5

  1. Check Transaxle Range switch circuit; use a scan tool and be sure the scan tool indicates that the vehicle is in drive with gear selector in drive or overdrive.
  2. If a problem is found, diagnose and repair Transaxle Range switch as necessary Refer to 4T60-E Automatic Transaxle Diagnosis.

Was a problem found?

--

Go to Step 14

Go to Step 6

6

  1. Check TCC operation. Refer to 4T60-E Transaxle Diagnosis.
  2. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 14

Go to Step 7

7

  1. Check for obvious overheating problems:
  2. • Low engine coolant.
    • Restricted air flow to radiator, or restricted water flow through radiator.
    • Inoperative electric cooling fan circuit(s), use the Electric Cooling Fan Diagnosis.
    • Correct coolant solution should be a 50/50 mix of approved antifreeze/coolant and water. Refer to Engine Cooling.
    • EGR operation-refer to DTC P0401.
  3. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 14

Go to Step 8

8

  1. Check fuel pressure. Refer to Fuel System Diagnosis.
  2. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 14

Go to Step 9

9

  1. Check items that can cause an engine to run lean (long term fuel trim significantly in the positive range). For a Lean condition, refer to Diagnostic Aids on diagnostic support page of DTC P0171.
  2. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 14

Go to Step 10

10

  1. Spark plugs for proper heat range. Refer to General Information.
  2. If incorrect spark plugs are installed, replace spark plugs as necessary.

Did any spark plugs require replacement?

--

Go to Step 14

Go to Step 11

11

  1. Remove excessive carbon buildup with a top engine cleaner. Refer to instructions on top engine cleaner can.
  2. Re-evaluate vehicle performance.

Is detonation still present?

--

Go to Step 12

Go to Step 14

12

  1. Check for an engine mechanical problem. Perform a cylinder compression check (refer to Engine Mechanical section).
  2. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 14

Go to Step 13

13

  1. Review all diagnostic procedures within this table.
  2. If all procedures have been completed and no malfunctions have been found, review/inspect the following:
  3. • Visual/physical inspection.
    • Scan Tool data.
    • Freeze Frame data/Failure Records Data.
    • All electrical connections within a suspected circuit and/or system.
  4. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 14

Review Technical Service Bulletins

14

Operate the vehicle to duplicate conditions present when the original symptom was noted.

Is symptom still present?

--

Go to Step 3

Repair complete