GM Service Manual Online
For 1990-2009 cars only

Valve Stem Oil Seal and Valve Spring Replacement Intake

Tools Required

    • J 36588 Valve Spring Compressor T-bolt
    • J 5892-D Valve Spring Compressor
    • J 36011 Spark Plug Wire Remover
    • J 36017 Valve Guide Seal Remover
    • J 36660-A Torque Angle Meter

Removal Procedure

    Important: If you loosen or remove the bolts which secure the camshaft housing to the cylinder head, replace the gasket between the camshaft housing and the cylinder head.

  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engne Electrical.
  2. Disconnect the ignition coil and module electrical connections.

  3. Object Number: 33641  Size: SH
  4. Remove the ignition coil and module cover bolts.
  5. Remove the ignition coil and module cover by pulling straight up.
  6. If the connector assembly is stuck to the spark plugs, use the J 36011 in order to remove the connector assembly. First twist and then pull up on the connector assembly.
  7. Disconnect the oil pressure switch electrical connector.
  8. Disconnect the timing chain housing at the exhaust camshaft housing, but do NOT remove the housing from the vehicle. Refer to Timing Chain Housing Replacement .
  9. Notice: Turn the camshaft housing upside down as soon as it is removed from the cylinder head. The lifters will fall out of the camshaft housing if it is not turned upside down. the lifters can be damaged if they fall out and hit a hard surface.

    Important: Use the reverse of the tightening procedure when loosening the retaining bolts which secure the camshaft housing to the cylinder head.


    Object Number: 33644  Size: SH
  10. Remove the camshaft housing bolts.
  11. Remove the camshaft housing.
  12. Remove the camshaft housing gasket.
  13. Remove the spark plug.
  14. Using a suitable adapter, apply air pressure to the cylinder.

  15. Object Number: 61031  Size: SH
  16. Compress the valve spring. Use the J 5892-D and the J 36588 .

  17. Object Number: 33711  Size: SH
  18. Disassemble the following components:
  19. • The valve keys
    • The retainer
    • The spring
    • The valve seal (using J 36017 )

    Object Number: 388959  Size: SH
  20. Disassemble the following components:
  21. • The rotator (intake)
    • The valve spring seat (exhaust)

    Object Number: 388964  Size: SH
  22. Assemble the rotator (intake).

  23. Assemble the valve spring seat (exhaust).
  24. Install a new, clean and dry valve seal. Push the seal on by hand in order to seat the seal fully.

  25. Object Number: 61031  Size: SH
  26. Install the spring and retainer. Use the J 36588 , and the J 5892-D in order to compress the valve spring.
  27. The valve keys
  28. Inspect for proper valve key seating.

Installation Procedure

  1. Remove the air line adapter.
  2. Install the spark plug.
  3. Notice: Carefully roll the camshaft housing right side up as it is installed onto the cylinder head. The lifters can be damaged if they fall out and hit a hard surface.


    Object Number: 33642  Size: SH
  4. Install the camshaft housing.
  5. Apply pipe sealant GM P/N 1052080 or equivalent to the threads of the camshaft housing bolt.

  6. Object Number: 61312  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  7. Use the J 36660-A in order to install the bolts. Install the bolts in sequence.
  8. Tighten
    Tighten the camshaft housing bolts to 15 N·m (11 lb ft).

  9. Install the timing chain housing to the camshaft housing and timing chain. Refer to Timing Chain Housing Replacement .
  10. Connect the electrical connection to the oil pressure switch.

  11. Object Number: 388971  Size: SH
  12. If any spark plug boot connector assembly has stuck to a spark plug, reinstall the connector onto the ignition coil and the module assembly.
  13. Place the ignition coil and module assembly over the spark plugs and push straight down.

  14. Object Number: 33641  Size: SH
  15. Clean any lubricant that is present on the ignition coil and on the bolts which secure the module assembly to the camshaft housing.
  16. Apply pipe sealant GM P/N 1052080 or equivalent onto the ignition coil and onto the bolts which secure the module assembly to the camshaft housing.
  17. Install the ignition coil and module cover bolts.
  18. Tighten
    Tighten the ignition coil and module cover bolts to 15 N·m (11 lb ft) + 30 degrees.


    Object Number: 388972  Size: SH
  19. Connect the electrical connector to the ignition coil and to the module.
  20. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.

Valve Stem Oil Seal and Valve Spring Replacement Exhaust

Tools Required

    • J 36588 Valve Spring Compressor T-Bolt
    • J 5892-D Valve Spring Compressor
    • J 36017 Valve Guide Seal Remover
    • J 36660-A Torque Angle Meter

Removal Procedure

Important: Any time the camshaft housing to the cylinder head bolts are loosened or removed, the camshaft housing to the cylinder head gasket must be replaced.

  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.

  2. Object Number: 33641  Size: SH
  3. Remove the ignition coil and module assembly. Refer to Ignition Control Module Replacement in Engine-Engine Controls.
  4. Disconnect the electrical connection from the oil pressure switch.
  5. Disconnect the timing chain housing at the camshaft housing, but do not remove it from the vehicle. Refer to Timing Chain Housing Replacement .
  6. Notice: Turn the camshaft housing upside down as soon as it is removed from the cylinder head. The lifters will fall out of the camshaft housing if it is not turned upside down. the lifters can be damaged if they fall out and hit a hard surface.

    Important: Use the reverse of the tightening procedure when loosening the camshaft housing to the cylinder head retaining bolts.


    Object Number: 33644  Size: SH
  7. Remove the camshaft housing. Refer to Exhaust Camshaft, Housing and Lifter Replacement or Intake Camshaft, Housing and Lifter Replacement in Engine-Engine Mechanical.
  8. Remove the spark plug.
  9. Using a suitable adapter, apply air pressure to the cylinder.

  10. Object Number: 61031  Size: SH
  11. Compress the valve spring. Use the J 5892-D and the J 36588 .

  12. Object Number: 33711  Size: SH
  13. Disassemble the following components:
  14. • The valve keys
    • The retainer
    • The spring
    • The valve seal using J 36017
    • The rotator (intake)
    • The valve spring seat (exhaust)

Installation Procedure

  1. Assemble the following components:
  2. • The rotator (intake)
    • The valve spring seat (exhaust)
    • A new, clean and dry valve seal. Push the seal on by hand in order to ensure that the seal is fully seated.
    • The spring and retainer. Use the J 36588 , and the J 5892-D in order to compress the valve spring.
    • The valve keys
  3. Inspect for proper valve key seating.
  4. Remove the air line adapter.
  5. Install the spark plug.
  6. Notice: Carefully roll the camshaft housing right side up as it is installed onto the cylinder head. The lifters can be damaged if they fall out and hit a hard surface.


    Object Number: 33642  Size: SH
  7. Install the camshaft housing. Refer to Exhaust Camshaft, Housing and Lifter Replacement or Intake Camshaft, Housing and Lifter Replacement in Engine-Engine Mechanical.

  8. Object Number: 61312  Size: SH
  9. Install the timing chain housing to the camshaft housing and timing chain. Refer to Timing Chain Housing Replacement .
  10. Connect the electrical connection to the oil pressure switch.
  11. Install the ignition coil and module assembly. Refer to Ignition Control Module Replacement in Engine-Engine Controls.
  12. Connect the electrical connector to the ignition coil and module assembly.
  13. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.