GM Service Manual Online
For 1990-2009 cars only

Removal Procedure

Tools Required

J 43828 Ball Joint Separator

  1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Notice: Care must be exercised to prevent the drive axle joints from being over-extended. When either end of the shaft is disconnected, over-extension of the joint could result in separation of the internal components and possible joint failure. Drive axle joint boot protectors should be used any time service is performed on or near the drive axles. Failure to observe this can result in interior joint or boot damage and possible joint failure.

  3. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  4. Remove the wiring harness from the lower control arm.
  5. Remove the stabilizer shaft link. Refer to Stabilizer Shaft Link Replacement .

  6. Object Number: 186841  Size: SH
  7. Remove the cotter pin (1) and the nut (2) from the ball joint stud (3).

  8. Object Number: 490085  Size: SH

    Notice: Use only the recommended tool for separating the ball joint from the knuckle. Failure to use the recommended tool may cause damage to the ball joint and seal.

  9. Separate the ball joint stud from the steering knuckle using the J 43828 .

  10. Object Number: 449077  Size: SH
  11. Remove the bolts (7) and the nuts (8) from the lower control arm (9).
  12. Remove the rear crossmember bolts (3) from the lower control arm (9).
  13. Remove the lower control arm (9) from the crossmember (4).
  14. Install the control arm (4) into a vice.
  15. Drill out the three rivets retaining the ball joint to the lower control arm. Use a 3 mm (1/8 in) drill bit to make a pilot hole through the rivets. Finish drilling the rivets with a 13 mm (½ in) drill bit.
  16. Remove the ball joint from the lower control arm.

Installation Procedure


    Object Number: 165250  Size: SH
  1. Install the ball joint (4) in the control arm (2).
  2. Install the three ball joint bolts (3) and nuts (1) as shown on the instruction sheet in the ball joint kit. Tighten the ball joint bolts to specifications found in the ball joint kit.

  3. Object Number: 449077  Size: SH
  4. Install the lower control arm (9) to the crossmember (4).
  5. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  6. Install the rear crossmember bolts (3) to the lower control arm (9).
  7. Tighten
    Tighten the bolt to 245 N·m (180 lb ft) plus 180 degrees of rotation.

  8. Install the bolts (7) and the nuts (8) to the lower control arm (9).
  9. Tighten
    Tighten the bolts to 115 N·m (84 lb ft).


    Object Number: 186841  Size: SH
  10. Install the steering knuckle to the ball joint stud (3).
  11. Install the nut (2) to the ball joint stud (3).
  12. Tighten
    Tighten the nut to 55 N·m (41 lb ft) minimum, 65 N·m (55 lb ft) maximum, to install the cotter pin.

  13. Install the cotter pin (1).
  14. Install the stabilizer shaft link. Refer to Stabilizer Shaft Link Replacement .
  15. Install the wiring harness to the lower control arm.
  16. Install the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation .
  17. Lower the vehicle.
  18. Inspect the front wheel alignment. Refer to Wheel Alignment Measurement in Wheel Alignment.