Ignition and Start Switch Replacement Pontiac

1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
2. Remove the instrument panel (I/P) accessory trim plate. Refer to Instrument Panel Accessory Trim Plate Replacement .
3. Remove the I/P cluster. Refer to Instrument Cluster Replacement .



4. Remove the bolts from the ignition switch.



5. Reposition the ignition switch for ease of removal.
6. Insert the key and turn the ignition lock cylinder to the ON/RUN position.



7. Press the transaxle park/lock cable retainer to release the retainer, then pull to remove the park/lock cable from the ignition switch.
8. Remove the lock cylinder from the ignition switch:

8.1.	Depress and hold the ignition lock cylinder detent.

8.2.	Turn the key to the ON/RUN position.

8.3.	Pull the ignition lock cylinder out with the key.





Important: Remove the ignition lock cylinder before you remove the Passlock™ electrical connector.

9. Disconnect the Passlock™ electrical connector from the ignition switch.



10. Disconnect the electrical connectors from the ignition switch.
11. Remove the ignition switch through the I/P cluster opening.



12. If the lock cylinder does not rotate or is seized, perform the following procedure:

12.1.

Protect the immediate work area with suitable material such as clean shop towels or a clean fender cover.

12.2.

Locate the surface for the ignition lock cylinder release button (2) on the plastic ignition switch housing and center punch a location (1) on the rib 9.5 mm (3/8 in) rearward, toward the key entry end, from the cylinder release button.

12.3.

Carefully drill a pilot hole through the plastic housing with an 1/8-inch drill bit.

12.4.

Carefully drill a larger hole at the pilot location, and slightly into the ignition lock cylinder surface to break the release button retaining spring using a 9/32-inch drill bit.

12.5.

Remove portions of the broken spring from the hole using a small suitable tool.

12.6.

Grasp the ignition lock cylinder and remove the cylinder from the switch housing.

12.7.

Remove any plastic flashing from the drilling operation, and using compressed air blow out the ignition switch assembly.

12.8.

Follow the service manual procedures when cylinder coding is required. Refer to Key and Lock Cylinder Coding in General Information.

1. If the lock cylinder would not rotate or was seized, perform the following procedure:

1.1.	Install the new ignition lock cylinder as required by rotating both the cylinder and the ignition switch to the ON/RUN position.

1.2.	Push the lock cylinder into the ignition switch housing until fully seated.

1.3.	You may need to slightly press the release button as the cylinder passes by the 9/32-inch hole previously drilled in the ignition switch housing.




2. Position the ignition switch into position through the I/P cluster opening.
3. Connect the electrical connectors to the ignition switch.



4. Connect the Passlock™ electrical connector to the ignition switch.



5. Connect the park/lock cable to the ignition switch.
6. Insert the key and turn the ignition lock cylinder to the ON/RUN position.



7. Install the ignition lock cylinder. If you turned the key slightly while removing the lock cylinder, you may have to align the white colored ignition switch rotor (1) with the lock cylinder (2). You can rotate the ignition switch rotor (1) with your finger.
8. Remove the key from the lock cylinder.



9. Position the ignition switch to the I/P.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

10. Install the bolts to the ignition switch.

Tighten
Tighten the bolts to 10 N·m (89 lb in).

11. Install the I/P cluster. Refer to Instrument Cluster Replacement .
12. Install the I/P accessory trim plate. Refer to Instrument Panel Accessory Trim Plate Replacement .
13. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
14. Perform the Passlock™ learn procedure. Refer to Programming Theft Deterrent System Components in Theft Deterrent.

Ignition and Start Switch Replacement Oldsmobile

1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electric.
2. Remove the radio. Refer to Radio Replacement in Entertainment.
3. Remove the instrument panel (I/P) cluster. Refer to Instrument Cluster Replacement .



4. Remove the screws from the ignition switch bracket.



5. Reposition the ignition switch to the cluster opening for access.
6. Remove the bolts which secure the ignition switch to the bracket.



7. Remove the bracket.



8. Insert the key and turn the lock cylinder to the ON/RUN position.



9. Depress the transaxle park/lock cable retainer to release the cable. Pull the park/lock cable away from the ignition switch.
10. Remove the lock cylinder from the ignition switch:

10.1.

Depress and hold the ignition lock cylinder detent.

10.2.

Turn the key to the ON/RUN position.

10.3.

Pull the ignition lock cylinder out with the key.





Important: Remove the lock cylinder before you remove the Passlock™ electrical connector.

11. Disconnect the Passlock™ electrical connector from the ignition switch.



12. Disconnect the electrical connectors from the ignition switch.



13. Remove the ignition switch through the I/P cluster opening.



14. If the lock cylinder does not rotate or is seized, perform the following procedure:

14.1.

Protect the immediate work area with suitable material, such as clean shop towels or a clean fender cover.

14.2.

Locate the surface for the release button (2) on the plastic ignition switch housing, and center punch a location (1) on the rib 9.5 mm (3/8 in) rearward, toward the key entry end, from the cylinder release button.

14.3.

Use an 1/8-inch drill bit and carefully drill a pilot hole through the plastic housing.

14.4.

Use a 9/32-inch drill bit and carefully drill a larger hole at the pilot location, slightly into the lock cylinder surface, to break the release button retaining spring.

14.5.

Remove portions of the broken spring from the hole using a small suitable tool.

14.6.

Grasp the lock cylinder and remove the cylinder from the switch housing.

14.7.

Remove any plastic flashing from the drilling operation, and using compressed air, blow out the ignition switch assembly.

14.8.

Follow the service manual procedures when cylinder coding is required. Refer to Key and Lock Cylinder Coding .

1. If the lock cylinder would not rotate or was seized, perform the following procedure:

1.1.	Install the new lock cylinder as required by rotating both the cylinder and the ignition switch to the ON/RUN position.

1.2.	Push the lock cylinder into the ignition switch housing until the cylinder is fully seated.

1.3.	Slightly depress the release button as the cylinder passes by the 9/32-inch hole previously drilled in the ignition switch housing.




2. Position the ignition switch into position through the I/P cluster opening.
3. Connect the electrical connectors to the ignition switch.



4. Connect the Passlock™ electrical connector to the ignition switch.



5. Connect the park/lock cable to the ignition switch.



6. Position the bracket to the ignition switch.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

7. Install the ignition switch bolts.

Tighten
Tighten the bolts to 10 N·m (89 lb in).




8. Insert the key and turn the lock cylinder to the ON/RUN position.
9. Install the lock cylinder to the switch.



10. If you turned the key slightly while removing the lock cylinder, you may have to align the white colored ignition switch rotor (1) with the lock cylinder (2). You can rotate the ignition switch rotor (1) with your finger.
11. Remove the key from the lock cylinder.



12. Position the ignition switch to the switch opening.
13. Install the ignition switch bracket screws.

Tighten
Tighten the screws to 2 N·m (18 lb in).

14. Install the I/P cluster. Refer to Instrument Cluster Replacement .
15. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
16. Perform the Passlock™ learn procedure. Refer to Programming Theft Deterrent System Components in Theft Deterrent.