Scan Tool Does Not Communicate with Class 2 Device. Oldsmobile Aurora 2001

For 1990-2009 cars only

Makes 🢒 Oldsmobile 🢒 2001 🢒 Aurora 🢒 Engine 🢒 Engine Electrical 🢒 Scan Tool Does Not Communicate with Class 2 Device

Circuit Description

Modules connected to the class 2 serial data circuit monitor for serial data communications during normal vehicle operation. Operating information and commands are exchanged among the modules. Connecting a scan tool to the Data Link Communications (DLC) allows communication with the modules for diagnostic purposes.

Diagnostic Aids

The engine will not start when there is a total malfunction of the class 2 serial data circuit while the engine is not running.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

A partial malfunction in the class 2 serial data circuit uses a different procedure from a total malfunction of the class 2 serial data circuit.

The following DTCs may be retrieved with a history status. These DTCs are not the cause of the present condition:

A State of Health DTC with a history status may be present along with a U1000 or a U1255 with a current status. This indicates that the malfunction occurred when the ignition was on.

The memory seat module (MSM) and the remote control door lock receiver (RCDLR) are not monitored by other modules. When one of these modules is not communicating, diagnose the malfunction using the specified procedure.

Data link connector terminals 2 and 5 provide the connection to the class 2 serial data circuit and the signal ground circuit respectively.

An open in the class 2 serial data circuit between the DLC and connector C201 will prevent the scan tool from communicating with any module. This condition will not set a DTC.

The class 2 serial data circuit is shorted to voltage or to ground. The condition may be due to the wiring or due to a malfunction in one of the modules. When you test the wiring for a short, make sure there is not a module connected to the wire being tested.

If communication can be established, the malfunction is in one of the following modules, or the wiring between these devices:

•	The inflatable restraint sensing and diagnostic module (SDM)

•	The rear integration module (RIM)

•	The remote playback device - CD changer, w/U1S

•	The vehicle interface unit (VIU) w/UE1

If communication can be established, the malfunction is in the remote control door lock receiver (RCDLR), or the wiring between the RCDLR and the RIM.

If communication can be established, the malfunction is in the electronic brake control module (EBCM); the memory seat module (MSM) w/A45; or the wiring between these devices and the RCDLR. If communication cannot be established, the malfunction is in the powertrain control module (PCM), or the wiring between the PCM and the EBCM.

If communication can be established, the malfunction is in the driver door module (DDM), or the wiring between the DDM, PCM and the flex wire harness.

If communication cannot be established, the malfunction is in the wiring between the DDM, PCM, and connector C215.

If communication can be established, the malfunction is in the driver information center (DIC); the radio; the instrument panel cluster (IPC); or the flat wire harness. When the malfunction is in the flex wire harness, the flex wire harness must be replaced. If communication cannot be established, the malfunction is in the inflatable restraint sensing and diagnostic module (SDM); the dash integration module (DIM); the theft deterrent control module; the instrument panel integration module (IPM); or the wiring connected to the DLC.

Since the short is not in the wiring harness the malfunction is due to one of the modules.

If there are no current DTCs that begin with a U, the communication malfunction has been repaired.

The communication malfunction may have prevented diagnosis of the customer complaint.

Step

Action

Yes

Does the scan tool power up?

Go to Step 2

Go to Scan Tool Does Not Power Up

Turn ON the ignition with the engine OFF.
Attempt to communicate with each module on the class 2 serial data circuit. If using a Tech 2, obtain this information using the Class 2 Message Monitor feature.

Does the scan tool communicate with any module on the class 2 serial data circuit?

Go to Step 3

Go to Step 7

Select the Display DTCs function for each module. If using a Tech 2, use the Class 2 DTC Check feature in order to determine which modules do have DTCs set.
Record all of the displayed DTCs, the DTC status and the module which set the DTC.

Did you record any DTCs in the range of U1000 to U1305?

Go to Step 4

Go to Diagnostic Trouble Code (DTC) List

Are the DTCs U1300, U1301 or U1305 retrieved from any module?

Go to Step 5

Go to Step 6

Important:: Turn ON the ignition, with the engine OFF, when testing for a short to voltage. Use the DMM MIN/MAX function to capture intermittent conditions.

Test the class 2 serial data circuit for an intermittent short to ground or an intermittent short to voltage. Refer to the following in Wiring Systems:

•	Testing for Intermittent Conditions and Poor Connections

•	Circuit Testing

•	Connector Repairs

•	Wiring Repairs

Did you find and correct the condition?

Go to Step 30

Go to Step 6

Are U1000 or U1255 the only DTCs displayed in the previously specified range?

Go to DTC U1000 and U1255

Go to Step 7

Diagnose the malfunction using the DTC U1001 - U1254 Loss of XXX Communications procedures for the module which is not communicating. Refer to DTC U1001-U1254 .

Did you complete the action?

Go to the Control Module References in Body Control System for the applicable Diagnostic System Check

Turn OFF the ignition.
Disconnect the scan tool from the data link connector (DLC).
Inspect for poor connections and terminal tension at the DLC. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to the Control Module References in Body Control System for the applicable Diagnostic System Check

Go to Step 9

Turn OFF the ignition.
Test the ground circuits of the DLC for an open.

Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to the Control Module References in Body Control System for the applicable Diagnostic System Check

Go to Step 10

Turn OFF the ignition.
Test the class 2 serial data circuit between the DLC for C201.

Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to the Control Module References in Body Control System for the applicable Diagnostic System Check

Go to Step 11

Disconnect the PCM.
Disconnect the SDM.
Install a scan tool.
Turn ON the ignition leaving the engine OFF.
Attempt to communicate with any module still connected to the DLC through the class 2 serial data circuit.

Does the scan tool communicate with any module on the class 2 serial data circuit?

Go to Step 12

Go to Step 19

Turn OFF the ignition.
Reconnect the PCM.
Disconnect the RIM.
Turn ON the ignition leaving the engine OFF.
Attempt to communicate with any module still connected to the DLC through the class 2 serial data circuit.

Does the scan tool communicate with any module on the class 2 serial data circuit?

Go to Step 13

Go to Step 14

Turn OFF the ignition.
Disconnect all modules on the class 2 serial data circuit between the RIM and the SDM.
Test the class 2 serial data circuit between the RIM and the SDM for a short to ground or a short to voltage. Turn ON the ignition leaving the engine OFF when you test for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 30

Go to Step 26

Turn OFF the ignition.
Disconnect the RCDLR.
Turn ON the ignition leaving the engine OFF.
Attempt to communicate with any module still connected to the DLC through the class 2 serial data circuit.

Does the scan tool communicate with any module on the Class 2 serial data circuit?

Go to Step 15

Go to Step 16

Turn OFF the ignition.
Test the class 2 serial data circuit between the RCDLR and the RIM for a short to ground or a short to voltage. Turn ON the ignition leaving the engine OFF when you test for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 30

Go to Step 26

Turn OFF the ignition.
Disconnect the EBCM.
Turn ON the ignition leaving the engine OFF.
Attempt to communicate with any module still connected to the DLC through the class 2 serial data circuit.

Does the scan tool communicate with any module on the class 2 serial data circuit?

Go to Step 17

Go to Step 18

Turn OFF the ignition.
Test the class 2 serial data circuit between the EBCM and the RCDLR for a short to ground or a short to voltage. Turn ON the ignition leaving the engine OFF when you test for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 30

Go to Step 26

Turn OFF the ignition.
Test the class 2 serial data circuit between the PCM and the EBCM for a short to ground or a short to voltage. Turn ON the ignition leaving the engine OFF when you test for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 30

Go to Step 26

Turn OFF the ignition.
Disconnect connector C215.
Turn ON the ignition leaving the engine OFF.
Attempt to communicate with any module still connected to the DLC through the class 2 serial data circuit.

Does the scan tool communicate with any module on the class 2 serial data circuit?

Go to Step 20

Go to Step 22

Turn OFF the ignition.
Connect connector C215.
Disconnect the driver door module (DDM).
Turn ON the ignition leaving the engine OFF.
Attempt to communicate with any module still connected to the DLC through the class 2 serial data circuit.

Does the scan tool communicate with any module on the class 2 serial data circuit?

Go to Step 28

Go to Step 21

Test the class 2 serial data circuit between the following components.

•

C215

•

DDM

•

PCM

Turn ON the ignition leaving the engine OFF when you test for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 30

Go to Testing for Electrical Intermittents in Wiring Systems

Turn OFF the ignition.
Disconnect connector C216.
Turn ON the ignition leaving the engine OFF.
Attempt to communicate with any module still connected to the DLC through the class 2 serial data circuit.

Does the scan tool communicate with any module on the class 2 serial data circuit?

Go to Step 23

Go to Step 24

Turn OFF the ignition.
Disconnect all modules on the class 2 serial data circuit between the C215 and the C216.
Test the class 2 serial data circuit between the C215 and the C216 for a short to ground or a short to voltage. Turn ON the ignition leaving the engine OFF when you test for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find the condition?

Go to Step 25

Go to Step 26

Turn OFF the ignition.
Disconnect all modules on the class 2 serial data circuit between the C216 and the SDM.
Test the class 2 serial data circuit between the C216 and the SDM for a short to ground or a short to voltage. Turn ON the ignition leaving the engine OFF when you test for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 30

Go to Step 26

Replace the flat wiring harness.

Did you complete the action?

Go to Step 30

Connect all of the disconnected modules except for those in the suspect area of the class 2 serial data circuit.
Connect any other disconnected in-line connectors.
Connect one of the disconnected modules in the suspect area of the class 2 serial data circuit.
Install a scan tool.
Turn ON the ignition leaving the engine OFF.
Attempt to communicate with any module still connected to the DLC through the class 2 serial data circuit.

Does the scan tool communicate with any module on the class 2 serial data circuit?

Go to Step 27

Go to Step 29

Continue connecting the disconnected modules and attempting to communicate after each connection until communication cannot be established or all the modules are connected.

Did you find the condition?

Go to Step 29

Go to Testing for Electrical Intermittents in Wiring Systems

Replace the DDM. Refer to Control Module References for the applicable replacement procedure.

Did you complete the replacement?

Go to Step 30

Important: Perform the module setup procedure if required.

Replace the most recently connected module. Refer to Control Module References in Body Control System for the appropriate Repair Instructions for module replacement.

Did you complete the replacement?

Go to Step 30

Connect all of the modules.
Connect any other connectors.
Install a scan tool.
Turn ON the ignition leaving the engine OFF.

Important: The scan tool may require a power up reset before communication will occur due to a short on the class 2 serial data circuit. Turn off or disconnect the scan tool before you display DTCs.

Wait for 10 seconds.
Select the display DTCs function for each module. If using a Tech 2, use the Class 2 DTC Check feature in order to determine which modules do have DTCs set.
Record all of the displayed DTCs and the DTC status.

Did you record any DTCs which begin with a U and with a current status?

Go to Step 32

Go to Step 31

Did you record any DTCs which do not begin with a U?

Go to Step 32

Go to Step 34

Diagnose the DTCs as directed by the diagnostic procedures for the particular module or malfunction. The PCM may have DTCs P1602 to P1615, or P1626 set. If only P1600 DTCs in the range specified along with history U1XXX DTCs are set and the vehicle will start and run, the action is complete.

Did you complete the action?

Go to Step 33

Did you diagnose all of the DTCs?

Go to Step 34

Go to Step 32

Use the scan tool in order to clear the DTCs.

Did you complete the action?

System OK