Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests for continuity through the 24K ohms resistor in the windshield wiper/washer switch. The connector behind the instrument panel knee bolster is suitable for performing this step.
-
This step tests for continuity through the delay resistors in the windshield wiper/washer switch. The measured resistance will change in sequence from high to low as the delay speed is increased. The connector behind the instrument panel knee bolster is suitable for performing this step.
Step | Action | Value(s) | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Wiper/Washer Schematics Connector End View Reference: Wiper/Washer Connector End Views | ||||||||||||
1 | Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections? | -- | Go to Step 2 | |||||||||
2 |
Does the windshield wiper/washer system operate normally? | -- | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 | ||||||||
3 | Do the windshield wipers operate in the high speed mode? | -- | Go to Step 5 | Go to Step 4 | ||||||||
4 |
Does the test lamp illuminate? | -- | Go to Step 12 | Go to Step 9 | ||||||||
5 |
Does the test lamp illuminate? | -- | Go to Step 6 | Go to Step 10 | ||||||||
6 |
Does the test lamp illuminate in the listed switch positions? | -- | Go to Step 7 | Go to Step 11 | ||||||||
Is the resistance at or near the specified value in all the listed switch positions? | 24K ohms | Go to Step 8 | Go to Step 14 | |||||||||
Does the resistance remain within the specified values from high to low as the delay speed is increased? | 38K - 690K ohms | Go to Step 13 | Go to Step 14 | |||||||||
9 | Test the windshield wiper motor high speed circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 18 | Go to Step 14 | ||||||||
10 | Test the windshield wiper switch signal 2 circuit for an open or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 18 | Go to Step 14 | ||||||||
11 | Test the windshield wiper switch signal 1 circuit for an open or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 18 | Go to Step 14 | ||||||||
12 |
Did you find and correct the condition? | -- | Go to Step 18 | Go to Step 16 | ||||||||
13 |
Did you find and correct the condition? | -- | Go to Step 18 | Go to Step 16 | ||||||||
14 | Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 18 | Go to Step 15 | ||||||||
15 | Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement in Steering Wheel and Column. Is the repair complete? | -- | Go to Step 18 | -- | ||||||||
16 | Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 18 | Go to Step 17 | ||||||||
17 | Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement . Is the repair complete? | -- | Go to Step 18 | -- | ||||||||
18 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 3 | ||||||||
