GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The steering wheel controls are momentary contact switches that connect a series of resistors so that each switch selection corresponds to a fixed resistance value. The body control module (BCM) determines which switch has been pressed by the voltage drop across the corresponding resistance value. The BCM supplies voltage to the steering wheel controls through the rear wiper/washer switch supply voltage circuit. The BCM monitors the switch voltage on the remote radio control signal circuit.

Conditions for Running the DTC

This test is run every 125 milliseconds.

Conditions for Setting the DTC

The BCM detects a switch voltage that is higher than normal.

Action Taken When the DTC Sets

The BCM will ignore the switch command.

Conditions for Clearing the MIL/DTC

    • The DTC will become history if the BCM no longer detects a circuit malfunction.
    • The history DTC will clear after 100 fault free ignition cycles.
    • The DTC can be cleared with a scan tool.

Test Description

The number below refers to the step number on the diagnostic table.

  1. Tests for the proper operation of the circuit in the low voltage range.

Step

Action

Value(s)

Yes

No

Schematic Reference: HVAC Schematics

1

Did you perform the HVAC Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - HVAC Systems - Automatic

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the SWC Switch Voltage parameter in the Body Control Module data list .

Does the scan tool indicate that the SWC Switch Voltage parameter is near the specified value?

0 Volts

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 3

3

Caution: When you are performing service on or near the SIR components or the SIR wiring, you must disable the SIR system. Refer to Disabling the SIR System. Failure to follow the correct procedure could cause air bag deployment, personal injury, or unnecessary SIR system repairs.

  1. Disable the SIR system. Refer to Disabling the SIR System in SIR.
  2. Turn OFF the ignition.
  3. Disconnect the left steering wheel controls.
  4. Turn ON the ignition, with the engine OFF.
  5. With a scan tool, observe the SWC Switch Voltage parameter.

Does the scan tool indicate that the SWC Switch Voltage parameter is near the specified value?

0 Volts

Go to Step 6

Go to Step 4

5

  1. Turn OFF the ignition.
  2. Disconnect the right steering wheel controls.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the SWC Switch Voltage parameter.

Does the scan tool indicate that the SWC Switch Voltage parameter is near the specified value?

0 Volts

Go to Step 7

Go to Step 5

6

Test the signal circuit of the steering wheel controls for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 8

6

Inspect for poor connections at the harness connector of the left steering wheel control switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 9

7

Inspect for poor connections at the harness connector of the right steering wheel control switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 10

8

Inspect for poor connections at the harness connector of the body control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 11

9

Replace the left steering wheel control switch. Refer to Steering Wheel Control Switch Assembly Replacement in Steering Wheel and Column.

Did you complete the replacement?

--

Go to Step 12

--

10

Replace the right steering wheel control switch. Refer to Steering Wheel Control Switch Assembly Replacement in Steering Wheel and Column.

Did you complete the replacement?

--

Go to Step 12

--

11

Important: Perform the set up procedure for the body control module.

Replace the body control module. Refer to Body Control Module Replacement .

Did you complete the replacement?

--

Go to Step 12

--

12

  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

--

Go to Step 2

System OK