Front Wheel Drive Shaft Seal Replacement Left

Tools Required

1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
2. Remove the left front tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
3. Remove the left engine splash shield. Refer to Engine Splash Shield Replacement Body Front End.
4. Remove the left stabilizer shaft link from the left lower control arm. Refer to Stabilizer Shaft Link Replacement in Front Suspension.
5. Remove the left tie rod end from the left steering knuckle. Refer to Steering Knuckle Replacement in Front Suspension.
6. Remove the left lower ball joint from the left steering knuckle. Refer to Steering Knuckle Replacement in Front Suspension.



7. Disconnect the left drive axle from the transaxle. Refer to Wheel Drive Shaft Replacement in Drive Axle.
8. Secure the left drive axle to the left steering knuckle and strut.



9. Use the Axle boot remover J 23129 with slide hammer to pull out seal (409). Do NOT damage the seal bore.

Tools Required

1. Use a light wipe of transaxle fluid to lubricate the seal lip.



2. Use the J 34115 to install a new seal.
3. Install the J 37292-B in the seal.

Important: Carefully guide the axle shaft past the lip seal. Do NOT allow the shaft splines to contact any portion of the seal lip surface or damage to the seal will occur.

4. Connect the left drive axle to the transaxle. Refer to Wheel Drive Shaft Replacement in Drive Axle.
5. Remove the J 37292-B .
6. Install the left lower ball joint to the left steering knuckle. Refer to Steering Knuckle Replacement in Front Suspension.
7. Install the left tie rod end to the left steering knuckle. Refer to Steering Knuckle Replacement in Front Suspension.
8. Install the left stabilizer shaft link to the left lower control arm. Refer to Stabilizer Shaft Link Replacement in Front Suspension.
9. Install the left engine splash shield. Refer to Body Front End.
10. Install the left front tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
11. Lower the vehicle.
12. Adjust the fluid level.
13. Inspect for proper completion of the repairs.
14. Inspect for proper fluid level.
15. Inspect for fluid leaks.

Front Wheel Drive Shaft Seal Replacement Right

1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
2. Remove the right front tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
3. Remove the right engine splash shield. Refer to Engine Splash Shield Replacement Body Front End.
4. Remove the right stabilizer shaft link from the right lower control arm. Refer to Stabilizer Shaft Link Replacement in Front Suspension.
5. Remove the right tie rod end from the right steering knuckle. Refer to Steering Knuckle Replacement in Front Suspension.
6. Remove the right lower ball joint from the right steering knuckle. Refer to Steering Knuckle Replacement in Front Suspension.
7. Disconnect the right drive axle from the transaxle. Refer to Wheel Drive Shaft Replacement in Drive Axle.
8. Secure the right drive axle to the right steering knuckle and strut.



9. Use the Axle boot remover J 23129 with slide hammer to pull out seal (409). Do NOT damage the seal bore.

Tools Required

1. Use a light wipe of transaxle fluid to lubricate the seal lip.



2. Use the J 29130 to install a new seal.
3. Install the J 37292-B in the seal.

Important: Carefully guide the axle shaft past the lip seal. Do NOT allow the shaft splines to contact any portion of the seal lip surface or damage to the seal will occur.

4. Connect the right drive axle to the transaxle. Refer to Wheel Drive Shaft Replacement in Drive Axle.
5. Remove the J 37292-B .
6. Install the right lower ball joint to the right steering knuckle. Refer to Steering Knuckle Replacement in Front Suspension.
7. Install the right tie rod end to the right steering knuckle. Refer to Steering Knuckle Replacement in Front Suspension.
8. Install the right stabilizer shaft link to the right steering knuckle. Refer to Steering Knuckle Replacement in Front Suspension.
9. Install the right engine splash shield. Refer to Engine Splash Shield Replacement Body Front End.
10. Install the right front tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
11. Lower the vehicle.
12. Inspect for leaks and adjust the fluid level. Refer to Fluid Capacity Specifications .
13. Inspect for proper completion of the repairs.