GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Oldsmobile 🢒 1999 🢒 Intrigue 🢒 Body and Accessories 🢒 Lighting Systems 🢒 Multifunction Turn Signal Lever Replacement - On Vehicle

Removal Procedure
  1. Verify that the multifunction turn signal lever is in the center of the OFF position.

    2. Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

  2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.

    3. Object Number: 322934 Size: SH
  3. Disable the S.I.R. Refer to Disabling the SIR System in S.I.R.
  4. Remove the inflatable restraint steering wheel module. Refer to Inflatable Restraint Steering Wheel Module Replacement in S.I.R.
  5. Remove the steering wheel. Refer to Steering Wheel Replacement .
  6. Remove the upper and lower steering column trim covers. Refer to Steering Column Trim Covers - Disassemble - Off Vehicle .
  7. Remove 1 wire harness strap (2) from the wire harness assembly.
  8. Remove 1 wire harness strap (2) from the upper tilt head assembly (1).

    9. Object Number: 322946 Size: SH
  9. Pop the wire harness assembly (1) from the wire harness strap (2).

    10. Object Number: 322982 Size: SH
  10. Remove the 2 tapping screws (1).

    11. Remove the turn signal and multifunction switch assembly (2).

Installation Procedure
  1. Install the multifunction turn signal switch. Use a small flat-blade in order to compress the electrical contact and move the multifunction turn signal switch into position.

    2. Object Number: 322982 Size: SH
  2. Verify that the electrical contact rests on the canceling cam.

    3. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the multifunction turn signal switch assembly (2) and secure by using 2 pan head tapping screws (1).

    4. Tighten
    Tighten the multifunction turn signal switch screws to 7 N·m (62 lb in).


    Object Number: 322946 Size: SH
  4. Route the wire harness assembly (1) along the steering column jacket assembly.
  5. Pop the wire harness assembly (1) into the wire harness strap (2).

    6. Object Number: 322934 Size: SH
  6. Install 1 wire harness strap (2) to the upper tilt head assembly (1).

    7. Install 1 wire harness strap (2) onto the wire harness assembly.

  7. Verify that the lever is in the center or the OFF position.
  8. Install the inflatable restraint steering wheel module. Refer to Inflatable Restraint Steering Wheel Module Replacement .
  9. Install the upper and lower steering column trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .
  10. Install the steering wheel. Refer to Steering Wheel Replacement .
  11. Enable the S.I.R. Refer to Enabling the SIR System in S.I.R.
  12. Connect the negative battery cable.Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.