Step
| Action
| Value(s)
| Yes
| No
|
1
| Was the BCM diagnostic system check performed?
| --
|
Go to Step 2
| Go to
Diagnostic System Check - Body Control System
in Body Control System
|
2
| Check for Powertrain
Control Module (PCM) Diagnostic Trouble Codes (DTCs). Refer to
Powertrain On Board Diagnostic (OBD) System Check
(LX5) or
Powertrain On Board Diagnostic (OBD) System Check
(L36) in Engine Controls for more
information.
Are there any PCM DTCs present?
| --
| Go to Appropriate DTC Table in Engine Controls
|
Go to Step 3
|
3
|
- Connect a scan tool to the Data Link Connector (DLC).
- Using scan tool, select BCM data display inputs and monitor the
park brake switch input.
- While observing the scan tool, apply and then release the park
brake.
Does the scan tool indicate that the park brake input is off while the
park brake is released?
| --
|
Go to Step 7
|
Go to Step 4
|
4
|
- Turn the ignition switch off.
- Disconnect the scan tool from the DLC.
- Disconnect the BCM connector C1.
- Release the park brake.
- Using a test light, connect between B+ and the BCM connector C1
terminal D5.
Is the test light off?
| --
|
Go to Step
7
|
Go to Step 5
|
5
|
- Leave the test light connected from the previous step.
- Disconnect the park brake indicator switch electrical connector.
Is the test light off?
| --
|
Go to Step
8
|
Go to Step 6
|
6
|
- Leave the test light connected from the previous step.
- Disconnect the DRL module electrical connector C2.
Is the test light off?
| --
|
Go to Step
9
|
Go to Step 10
|
7
|
- Disconnect the scan tool from the DLC.
- Turn the ignition switch off.
- Reconnect connectors/components removed.
- Close all the vehicle doors.
- Apply the park brake.
- Step firmly and hold the brake pedal.
- Start the engine.
- While shifting the transaxle into DRIVE, listen to the chime.
- While the transaxle is in the DRIVE, release the park brake. Note
that the chime stops.
- Shift the transaxle into PARK.
- Turn the engine off.
Did the BCM stop the chime for the park brake reminder upon the releasing
the park brake while the transaxle was in DRIVE?
| --
|
Go to Step 11
|
Go to Step
12
|
8
| Replace the park brake switch. Refer to
Parking Brake Indicator Switch Replacement
in Park
Brake for service procedure.
Is the repair complete?
| --
|
Go to Step
13
| --
|
9
| Repair short to ground in circuit 1830.
Is the repair complete?
| --
|
Go to Step
13
| --
|
10
| Repair short to ground in circuit 233.
Is the repair complete?
| --
|
Go to Step
13
| --
|
11
| The malfunction is not present at this time. Refer to
Audible Warnings Circuit Description
for more information
regarding the operation of the park brake reminder.
Is the action complete?
| --
|
Go to Step
13
| --
|
12
|
- Replace the BCM. Refer to
Body Control Module Replacement
for service procedures.
- After BCM replacement, perform the Setup New BCM procedure. Refer
to
Body Control Module (BCM) Programming/RPO Configuration
in Body Control System.
Is the repair complete?
| --
|
Go to Step
13
| --
|
13
|
- Turn the ignition switch off.
- Reinstall the connectors/components removed.
- Check for BCM current DTCs. Refer to
Diagnostic Trouble Code (DTC) Displaying
in Body Control System.
Are there any BCM current DTCs present?
| --
| Go to
Diagnostic System Check - Body Control System
in Body Control System
| System OK
|
