GM Service Manual Online
For 1990-2009 cars only

Refer to Engine Controls Schematics

A/C Pressure Switch, TPS, MAP, ECT and IAT


Object Number: 590134  Size: FS
Handling ESD Sensitive Parts Notice
Handling ESD Sensitive Parts Notice
Engine Controls Component Views
Powertrain Control Module Description
Heated O2 Sensors
Fuel Injectors
OBD II Symbol Description Notice
.

Circuit Description

The engine coolant temperature (ECT) sensor contains a semiconductor--a device that changes resistance based on temperature. The ECT sensor has a signal circuit and a ground circuit. The PCM applies voltage of about 5.0 volts to the sensor on the signal circuit. The powertrain control module (PCM) monitors any voltage changes caused by changes in the resistance of the sensor, and uses this information to determine the engine coolant temperature.

When the engine coolant is cold, the sensor resistance is high, and the PCM signal voltage is only pulled down a slightly through the sensor to ground. The PCM, therefore, senses a high signal voltage or a low coolant temperature. When the engine coolant is warm, the sensor resistance is low, and the signal voltage is pulled down a greater amount. This causes the PCM to sense a low signal voltage or a high temperature.

Conditions for Running the DTC

Engine run time longer than 15 seconds.

Conditions for Setting the DTC

    • The ECT sensor signal indicates an engine coolant temperature more than 134°C (274°F).
    • Above condition present for at least 10 seconds

Action Taken When the DTC Sets

    • The PCM illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
    • The PCM records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the PCM stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the PCM records the operating conditions at the time of the failure. The PCM writes the conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC

    • The PCM turns the MIL OFF after 3 consecutive drive trips during which the diagnostic runs and passes.
    • A last test failed, or the current DTC, clears when the diagnostic runs and passes.
    • A History DTC clears after 40 consecutive warm-up cycles, if no other emission related diagnostic failures are reported.
    • Use a scan tool in order to clear the MIL diagnostic trouble code.
    • Interrupting the PCM battery voltage may or may not clear DTCs. This practice is not recommended. Refer to Powertrain Control Module Description , Clearing Diagnostic Trouble Codes.

Diagnostic Aids

Check for a skewed or incorrectly calibrated ECT Sensor. Refer to the Temperature Versus Resistance table .

If DTC P0117 cannot be duplicated, the information included in the Fail Records data can be useful in determining vehicle mileage since the DTC was last set.

If the problem is intermittent. Refer to Intermittent Conditions .

Test Description

Numbers below refer to the step numbers on the diagnostic table:

  1. Verifies that the malfunction is present

  2. If DTC P0117 can be repeated only by duplicating the Failure Records conditions, refer to Temperature Versus Resistance . The table may be used to test the ECT sensor at various temperatures to evaluate the possibility of a shifted sensor that may be shorted above or below a certain temperature. If this is the case, replace the ECT sensor. If the ECT sensor appears to be OK, the malfunction is intermittent; refer to Diagnostic Aids.

  3. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is being replaced, the new PCM must be programmed.

Step

Action

Value(s)

Yes

No

1

Did you perform the Powertrain On-Board Diagnostic (OBD) System Check?

--

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

2

Observe the engine coolant temperature (ECT) display on the scan tool.

Is the ECT more than the specified value?

130°C  (266°F)

Go to Step 4

Go to Step 3

3

  1. Turn the key to the OFF position, wait 15 seconds, then turn the key to the ON position.
  2. Review and record the Failure Records data.
  3. Operate the vehicle within the Failure Records conditions as noted.
  4. Using a scan tool, monitor the Specific DTC info for DTC P0117.

Does the scan tool indicate DTC P0117 failed this ignition?

--

Go to Step 4

Go to Diagnostic Aids.

4

  1. Disconnect the ECT sensor electrical connector.
  2. Observe the ECT display on the scan tool.

Is ECT less than the specified value?

-31°C  (-24°F)

Go to Step 6

Go to Step 5

5

  1. Turn the key to Off.
  2. Disconnect the PCM.
  3. Check the ECT signal circuit for a short to ground or a short to the sensor ground circuit.
  4. If the ECT signal circuit is shorted, repair it as necessary. Refer to Wiring Repairs in Wiring Systems.

Was a problem found and corrected?

--

Go to Step 8

Go to Step 7

6

Replace the ECT sensor. Refer to Engine Coolant Temperature Sensor Replacement .

Is the action complete?

--

Go to Step 8

--

7

Important: The replacement PCM must be programmed.

Replace the PCM. Refer to Powertrain Control Module Replacement/Programming

Is the action complete?

--

Go to Step 8

--

8

  1. Clear the DTCs with the scan tool.
  2. Turn the key to the Off position and wait 15 seconds.
  3. Operate the vehicle within the conditions that are required for this diagnostic to run. Refer to Conditions for Running the DTC.

Does the scan tool indicate that this test ran and passed?

--

Go to Step 9

Go to Step 2

9

Review the Captured Info using the scan tool.

Are there any DTCs that have not been diagnosed?

--

Go to the applicable DTC table

System OK