Circuit Description
When you first turn the ignition switch to the RUN position, the inflatable restraint sensing and diagnostic module (SDM) perform tests to diagnose critical malfunctions within itself. Next the SDM measures the IGNITION and the deployment loop voltages to make sure they are within their respective normal voltage ranges. Then the SDM proceeds with the RESISTANCE MEASUREMENT test. During one portion of the RESISTANCE MEASUREMENT test, the SDM does the following:
| • | Grounds the Driver Belt Low terminal 8 through an internal current sink. |
| • | Connects the Driver Belt High terminal 9 to an internal constant current source. This current produces proportional voltage drops in the deployment loop. |
| • | Measures the voltage difference between Driver Belt High and Driver Belt Low. |
| • | Calculates the resistance of the driver seat belt pretensioner deployment loop using the measured voltage. |
Conditions for Setting the DTC
| • | The driver and passenger seat belt pretensioner deployment loops are not open. |
| • | The driver and passenger seat belt pretensioner deployment loops are not shorted to voltage. |
| • | The driver seat belt pretensioner deployment loop is not shorted to ground. |
| • | The driver seat belt pretensioner deployment loop resistance is more than 2.85 ohms. The passenger seat belt pretensioner deployment loop consists of the following components: |
| - | Driver seat buckle side belt. |
| - | Harness wiring of CKT 2118. |
| - | Harness wiring of CKT 2119. |
| - | Connector terminal contact. |
The RESISTANCE MEASUREMENT test checks for this malfunction. This test only occurs once each ignition cycle when IGNITION is within the normal operating voltage range.
Action Taken When the DTC Sets
| • | The SDM sets a Diagnostic Trouble Code. |
| • | The SDM turns ON the AIR BAG warning lamp. |
Conditions for Clearing the DTC
| • | Current DTC |
| The resistance of the driver seat belt pretensioner deployment loop is less than 2.3 ohms and the ignition switch is cycled. |
| • | History DTC |
| - | You issue a scan tool CLEAR CODES command. |
| - | Once 250 malfunction free ignition cycles have occurred. |
When you issue a scan tool CLEAR CODES command and the malfunction is still present, the DTC will not reappear until the next ignition cycle.
Diagnostic Aids
A poor connection can cause an intermittent condition. Check the following for a poor connection:
| • | The passenger seat buckle side belt harness connector terminals A and B. |
| • | The SDM terminals 8 and 9. |
| • | The wire to terminal connections in CKT 2118. |
| • | The wire to terminal connections in CKT 2119. |
The diagnostic table directs the technician to note the entry value of LH PRETENS. RESIST. Comparing the value of LH PRETENS. RESIST. over multiple ignition cycles can be helpful in determining if an intermittent condition exists.
When measurements are requested in this table, use J 39200 Digital Multimeter with the correct terminal adapter from J 35616 Connector Test Adapter Kit. When a check for proper connection is requested, refer to Intermittents and Poor Connections . When a wire, connector or terminal repair is requested, use J-38125 Terminal Repair Kit and refer to Wiring Repair .
Test Description
The numbers below refer to the step numbers on the diagnostic table:
-
This test determines the driver seat buckle side belt deployment loop resistance measured by the inflatable restraint sensing and diagnostic module (SDM).
-
This test checks for proper contact or corrosion of the yellow 2-way connector.
-
This test isolates the malfunction to one side of the driver seat buckle side belt yellow 2-way connector.
-
This test checks for proper contact or corrosion of the SDM connector.
-
This test determines whether the malfunction is in CKT 2118.
-
This test determines whether the malfunction is in CKT 2119.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the SIR Diagnostic System Check performed? | -- | ||
Has LH PRETENS. RESIST. been read and recorded on the repair order? | -- | -- | ||
Are the terminals damaged or corroded? | -- | |||
4 | Replace the driver seat buckle side belt yellow 2-way body harness connector. Refer to Wiring Repair . Are the repairs complete? | -- | -- | |
5 | Check for proper connection at terminals A and B on the driver seat buckle side belt yellow 2-way connector. Are the terminals damaged or corroded? | -- | ||
6 | Check for proper connection at terminals A and B on the driver seat buckle side belt yellow 2-way connector. Are the terminals damaged or corroded? | -- | ||
7 | Replace the driver seat buckle side belt. Refer to Seat Buckle Side Belt Replacement . Has the driver seat buckle side belt been replaced? | -- | -- | |
8 |
Is LH PRETENS. RESIST. more than the specified value? | 2.8 ohms | ||
9 |
Are the repairs complete? | -- | -- | |
Is LH PRETENS. RESIST. more than the specified value? | 2.8 ohms | |||
11 |
Has the driver seat buckle side belt been replaced? | -- | -- | |
Is the harness connector damaged or corroded? | -- | |||
13 | Replace the SDM connector. Refer to Wiring Repair . Are the repairs complete? | -- | -- | |
14 | Check for proper connection at terminals 8 and 9 on the SDM. Are the terminals damaged or corroded? | -- | ||
15 | Check for proper connection at terminals 8 and 9 on the SDM. Are the terminals damaged or corroded? | -- | ||
16 | Replace the inflatable restraint Sensing and Diagnostic Module (SDM). Refer to Inflatable Restraint Sensing and Diagnostic Module Replacement . Are the repairs complete? | -- | -- | |
Is the resistance reading within the specified values? | 0-0.5 ohms | |||
18 | Repair the high resistance condition in CKT 2118. Are the repairs complete? | -- | -- | |
Is the resistance reading within the specified values? | 0-0.5 ohms | Go to Integrity Check | ||
20 | Repair the high resistance condition in CKT 2119. Are the repairs complete? | -- | -- | |
21 | Reconnect all the SIR components, make sure all the components are properly mounted. Have all the SIR components been reconnected and properly mounted? | -- | -- | |
22 | Clear all the SIR DTCs. Have all the DTCs been cleared? | -- | -- |
