GM Service Manual Online
For 1990-2009 cars only

Rear Seat Belt Retractor Replacement C Pillar

Removal Procedure

Tools Required

J 29843-9 Door Lock Striker and Seat Belt Tool


    Object Number: 179380  Size: SH
  1. Unsnap the cover from the upper seat belt (1) anchor.
  2. Use the J 29843-9 in order to remove the upper seat belt anchor bolt (2).
  3. Important: The lower seat belt anchor (4) attaches to the mini-buckle on the right side of the 60 percent seat cushion on vehicles equipped with a 60/40 split bench seat. Use a key or a small flat bladed tool in order to release the seat belt anchor from the mini-buckle.

  4. Lift the trim cover in order to expose the lower seat belt anchor bolt (5).
  5. Use the J 29843-9 in order to remove the bolt (5) securing the lower seat belt anchor (4) from the C-pillar.
  6. Unsnap the cup holder/armrest trim cover (3) from the passenger's side.
  7. Remove the left body side front trim panel. Refer to Trim Panel Replacement - Left Body Side Front in Interior Trim.

  8. Object Number: 179382  Size: SH
  9. Use the J 29843-9 in order to remove the bolt securing the seat belt retractor from the C-pillar.
  10. Remove the seat side belt retractor from the C-pillar.

Installation Procedure


    Object Number: 179382  Size: SH
  1. Install the seat belt retractor to the C-pillar.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Use the J 29843-9 in order to install the bolt securing the seat belt retractor to the C-pillar.
  4. Tighten
    Tighten the seat belt retractor bolt (C-pillar) to 43 N·m (32 lb ft).

  5. Install the left body side front trim panel. Refer to Trim Panel Replacement - Left Body Side Front in Interior Trim.

  6. Object Number: 179380  Size: SH
  7. Snap the cup holder/armrest trim cover (3) in place on the passenger's side.
  8. Use the J 29843-9 in order to install the bolt (5) securing the lower seat retractor side belt anchor (4) to the C-pillar.
  9. Tighten
    Tighten the lower seat belt anchor bolt (C-pillar) to 43 N·m (32 lb ft).

  10. Install the seat belt anchor to the mini-buckle on the vehicles with the 60/40 split bench.
  11. Use the J 29843-9 in order to install the bolt (2) securing the upper seat belt anchor (1).
  12. Tighten
    Tighten the upper seat belt anchor bolt (C-pillar) to 43 N·m (32 lb ft).

  13. Snap the cover onto the upper seat belt anchor (1).

Rear Seat Belt Retractor Replacement D Pillar

Removal Procedure

Tools Required

J 29843-9 Door Lock Striker and Seat Belt Tool


    Object Number: 179384  Size: SH
  1. Unsnap the cover (2) from the upper seat belt anchor.
  2. Use the J 29843-9 in order to remove the bolt (1) securing the upper seat belt anchor from the D-pillar (3).
  3. Remove the upper seat belt anchor from the D-pillar (3).
  4. Raise the carpeting in order to expose the lower seat belt anchor bolt (5).
  5. Use the J 29843-9 in order to remove the bolt (5) securing the lower seat belt anchor (4) from the floor.
  6. Unsnap the plastic trim cover from the D-pillar (3) trim panel. Slide the belt webbing through the slot.
  7. Remove the driver's side rear quarter trim with RPO-C34, rear A/C only. Refer to Trim Panel Replacement - Rear Quarter Lower in Interior Trim.

  8. Object Number: 179387  Size: SH
  9. Use the J 29843-9 in order to remove the bolt securing the retractor from the D-pillar.
  10. Remove the retractor side seat belt from the vehicle.
  11. Remove the retractor from the vehicle.

Installation Procedure


    Object Number: 179387  Size: SH
  1. Install the retractor side seat belt to the vehicle.
  2. Install the retractor to the vehicle.
  3. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  4. Use the J 29843-9 in order to install the bolt securing the retractor to the D-Pillar.
  5. Tighten
    Tighten the seat belt retractor bolt (D-pillar) to 43 N·m (32 lb ft).

  6. Install the driver's side rear quarter trim with RPO-C34 rear AC only. Refer to Trim Panel Replacement - Rear Quarter Lower in Interior Trim.

  7. Object Number: 179384  Size: SH
  8. Slide the belt webbing through the slotted trim cover. Then snap the plastic trim cover to the D-Pillar (3) trim panel.
  9. Install the lower seat belt anchor (4) to the floor.
  10. Use the J 29843-9 in order to install the bolt (5) securing the lower seat belt anchor (4) to the floor.
  11. Tighten
    Tighten the lower seat belt anchor bolt (D-pillar) to 43 N·m (32 lb ft).

  12. Install the upper seat belt anchor (1) to the D-Pillar (3).
  13. Use the J 29843-9 in order to install the bolt (1) securing the upper seat belt anchor to the D-Pillar (3).
  14. Tighten
    Tighten the upper seat belt anchor bolt (D-pillar) to 43 N·m (32 lb ft)

  15. Snap the cover (2) to the upper seat belt anchor.