Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Hazard Switch Signal | 2 | 2 | 2 | -- |
Left Front Turn Signal Lamp Supply Voltage | B3948 02 | B3948 05 | B3948 05 | -- |
Right Front Turn Signal Lamp Supply Voltage | B3949 02 | B3949 05 | B3949 05 | -- |
Left Rear Stop/Turn Signal Lamp Supply Voltage | B3950 02 | B3950 05 | B3950 05 | -- |
Right Rear Stop/Turn Signal Lamp Supply Voltage | B3951 02 | B3951 05 | B3951 05 | -- |
Left Turn Signal Switch Signal | 3 | 3 | 3 | -- |
Right Turn Signal Switch Signal | 3 | 3 | 3 | -- |
Hazard Switch Ground | -- | 2 | 2 | -- |
Left Rear Stop/Turn Lamp Ground | -- | 1 | 1 | -- |
Right Rear Stop/Turn Lamp Ground | -- | 1 | 1 | -- |
Turn Signal/Multifunction Switch Ground | -- | 3 | 3 | -- |
Turn Signal Lamp - LF Ground | -- | 1 | 1 | -- |
Turn Signal Lamp - RF Ground | -- | 1 | 1 | -- |
1. Turn Signal Lamps and/or Indicators Malfunction 2. Hazard Lamps Malfunction 3. Turn Signal Switch Malfunction | ||||
Circuit/System Description
Ground is applied at all times at G300 to the turn signal/multifunction switch. The turn signal lamps may only be activated with the ignition switch in the ON or START position. When the turn signal/multifunction switch is placed in either the TURN RIGHT or TURN LEFT position, ground is applied to the body control module (BCM) through either the right turn or left turn signal switch signal circuit. Battery voltage is applied at all times from the BATT MAIN 3 fuse to the BCM. The BCM then applies a pulsating voltage to the front and rear turn signal lamps. Ground for the left front turn signal lamp is supplied at G101. Ground for the right front turn signal lamp is supplied at G102. Ground for the left rear turn signal lamp is supplied at G400. Ground for the right rear turn signal lamp is supplied at G402.
Reference Information
Schematic Reference
Connector End View Reference
Lighting Systems Connector End Views
Electrical Information Reference
Scan Tool Reference
Circuit/System Verification
Ignition ON, observe the scan tool right and left turn signal switch parameters while cycling the turn signal switch between the left and right positions. The readings should toggle between ACTIVE and INACTIVE.
| ⇒ | If the readings do not change between the commanded states, refer to Turn Signal Switch Malfunction. |
| ⇒ | If the readings change between the commanded states and the turn signal indicators are inoperative, refer to Turn Signal Indicators Malfunction. |
Circuit/System Testing
Turn Signal Switch Malfunction
- Ignition OFF, disconnect the C2 harness connector at the turn signal/multifunction switch.
- Test for less than 1.0 ohm of resistance between the ground circuit terminal B and ground.
- Ignition ON, verify the scan tool left turn signal switch parameter is INACTIVE.
- Verify the scan tool right turn signal switch parameter is INACTIVE.
- Install a 3A fused jumper wire between the signal circuit terminal G and ground. Verify the scan tool left turn signal switch parameter is ACTIVE.
- Install a 3A fused jumper wire between the signal circuit terminal H and ground. Verify the scan tool right turn signal switch parameter is ACTIVE.
- If all circuits test normal, test or replace the turn signal/multifunction switch.
| ⇒ | If greater than the specified range, test the ground circuit for an open/high resistance. |
| ⇒ | If not the specified value, test the signal circuit terminal G for a short to ground. If the circuit tests normal, replace the BCM. |
| ⇒ | If not the specified value, test the signal circuit terminal H for a short to ground. If the circuit tests normal, replace the BCM. |
| ⇒ | If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM. |
| ⇒ | If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM. |
Turn Signal Lamps Malfunction
- Ignition OFF, disconnect the harness connector at the inoperative turn signal lamp.
- Test for less than 1.0 ohm of resistance between the ground circuit and ground.
- Connect a test lamp between the control circuit and the ground circuit.
- Command the appropriate turn signal lamp ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
- If all circuits test normal, test or replace the appropriate turn signal lamp assembly.
| ⇒ | If greater than the specified range, test the ground circuit for an open/high resistance. |
| ⇒ | If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM. |
| ⇒ | If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM. |
Turn Signal Indicators Malfunction
Ignition ON, with a scan tool perform the display test for the instrument panel cluster (IPC) and observe the turn signal lamp indicators.
| ⇒ | If the turn signal lamp indicators illuminate during the test, replace the BCM. |
| ⇒ | If the turn signal lamp indicators do not illuminate during the test or remain illuminated at all times, replace the IPC. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for BCM and IPC replacement, setup, and programming |
