GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Opel 🢒 2007 🢒 GT 🢒 Transmission/Transaxle 🢒 Manual Transmission - Aisin AR5 🢒 Transmission Case Cleaning and Inspection

Clutch Housing

    Object Number: 872999 Size: SH
  1. Clean the clutch housing in a suitable solvent and air dry.
  2. Inspect the clutch housing for the following conditions:
    3. • Cracks
    • Damaged mounting flanges
    • Damaged bolt holes

Front Case

    Object Number: 873000 Size: SH
  1. Clean the front case in a suitable cleaning solvent and air dry.

    2. Notice: Refer to Machined Surface Damage Notice in the Preface section.

  2. Remove the sealer from the case sealing surfaces.
  3. Inspect the case for being broken or cracked.
  4. Inspect the input shaft bearing bore (a) for the following conditions:
    5. • A spun bearing
    • Cracks
  5. Inspect the countershaft front bearing bore (b) for the following conditions:
    6. • A spun bearing
    • Cracks
  6. Replace the case assembly if any of the above conditions are found. The front case is only serviced with the intermediate case.
  7. Inspect the sealing surfaces for damage.
  8. Repair small scratches or nicks with a soft stone.
  9. Inspect the case threaded bolt holes for damage.
  10. Repair any damaged threads.
  11. Inspect the location pins (72) for being loose or missing.
  12. Repair or replace any damaged location pins.
  13. Inspect the shift shaft bushings (295) for excessive wear.
  14. Replace the case assembly if the shift shaft bushings (295) are faulty.
  15. Inspect the shift shaft bushing plugs (63 and 64) for leaking or damage.
  16. Replace the plugs if faulty. Refer to Transmission Case Disassemble and Transmission Case Assemble .

Extension Housing RWD

    Object Number: 1644179 Size: SH
  1. Clean the extension housing in a suitable cleaning solvent and air dry.

    2. Notice: Refer to Machined Surface Damage Notice in the Preface section.

  2. Remove the sealer from the extension sealing surfaces.
  3. Inspect the extension for being broken or cracked.
  4. Inspect the rear bushing (6) for wear or damage. The bushing is serviced only with the extension housing.
  5. Inspect the shift shaft bushings (297) for excessive wear.
  6. Replace the extension if any of the above conditions are found.
  7. Inspect the sealing surfaces for damage.
  8. Repair small scratches or nicks with a soft stone.
  9. Inspect the case threaded bolt holes for damage.
  10. Repair any damaged threads.
  11. Inspect the control lever restrictor assembly (91) for damage.

    12. Object Number: 881170 Size: SH
  12. Inspect the reverse control lever restriction operation for the following conditions:
    13. • Moves in and out
    • Rotates
  13. Replace the reverse control lever restriction if faulty. Refer to Transmission Extension Disassemble and Transmission Extension Assemble .

Intermediate Case

    Object Number: 873003 Size: SH
  1. Clean the intermediate case in a suitable cleaning solvent and air dry.

    2. Notice: Refer to Machined Surface Damage Notice in the Preface section.

  2. Remove the sealer from the case sealing surfaces.
  3. Inspect the case for being broken or cracked.
  4. Inspect the output shaft bearing bore (a) for the following conditions:
    5. • A spun bearing
    • Cracks
  5. Inspect the countershaft rear bearing bore (b) for the following conditions:
    6. • A spun bearing
    • Cracks
  6. Inspect the shift shaft bushings (296) for excessive wear.
  7. Replace the intermediate case if any of the above conditions are found. The intermediate case is only serviced with the front case.
  8. Inspect the sealing surfaces for damage.
  9. Repair small scratches or nicks with a soft stone.
  10. Inspect the case threaded bolt holes for damage.
  11. Repair any damaged threads.
  12. Inspect the location pins (71 and 72) for being loose or missing.
  13. Repair or replace any damaged location pins.

Input Shaft Bearing Retainer

    Object Number: 873005 Size: SH
  1. Clean the input shaft bearing retainer in a suitable cleaning solvent and air dry.

    2. Notice: Refer to Machined Surface Damage Notice in the Preface section.

  2. Remove the sealer from the retainer sealing surfaces.
  3. Inspect the bearing retainer for being broken or cracked.
  4. Replace the bearing retainer if any of the above conditions are found.
  5. Inspect the sealing surfaces for damage.
  6. Repair small scratches or nicks with a soft stone.