DTC P0562 ECM
Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC P0562: System Voltage Low - ECMDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
B+ | P0562 | P0562 | -- | -- |
Ground | -- | P0562 | -- | -- |
Circuit/System Description
The engine control module (ECM) monitors the battery voltage to ensure that the voltage stays within the proper range. Damage to components, and incorrect data may occur when the voltage is out of range.
Conditions for Running the DTC
The vehicle speed is greater than 8 km/h (5 mph).
Conditions for Setting the DTC
The ECM detects that the battery voltage is less than 10 V for 5 seconds.
Action Taken When the DTC Sets
DTC P0562 is a C type DTC.
Conditions for Clearing the DTC
DTC P0562 is a C type DTC.
Diagnostic Aids
A low voltage DTC in multiple modules indicates a concern in the charging system.
Reference Information
Schematic Reference
| • | Engine Controls Schematics for the 1.6L (LDE) and 1.8L (2HO) engines |
| • | Engine Controls Schematics for the 2.0L gasoline engines |
| • | Engine Controls Schematics for the 2.0L (LBS) diesel engine |
| • | Engine Controls Schematics for the 2.8L (LBW) engine |
Connector End View Reference
Description and Operation
Charging System Description and Operation
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing
- Engine running, accessories OFF, measure and record the battery voltage at the battery terminals. The voltage should be between 12.6 and 15.0 V.
- Ignition OFF, disconnect the harness connectors at the ECM.
- Ignition OFF and scan tool disconnected, open and close the driver door, and wait 1 minute. Test for less than 5 Ω between the ground circuit terminals listed below and ground.
- Verify that a test lamp illuminates between the B+ circuit terminals listed below and ground.
- If all circuits test normal, replace the ECM.
| ⇒ | If not within the specified range, refer to Charging System Test. |
| • | Terminal 1 X2 (1.6L A16LET, 2.0L, 2.8L) gasoline |
| • | Terminal 2 X2 (1.6L A16LET, 2.0L, 2.8L) gasoline |
| • | Terminal 4 X2 (1.6L A16LET, 2.0L, 2.8L) gasoline |
| • | Terminal 6 X2 (2.0L ) diesel |
| • | Terminal 73 X1 (1.6L A16XER, 1.8L) gasoline |
| ⇒ | If greater than the specified range, test the ground circuit for an open/high resistance. |
| • | Terminal 12 X2 (1.6L A16XER, 1.8L) gasoline |
| • | Terminal 46 X2 (2.0L ) diesel |
| • | Terminal 56 X2 (2.0L, 2.8L) gasoline |
| • | Terminal 70 X2 (1.6L A16LET) gasoline |
| ⇒ | If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References - for ECM replacement, setup, and programming.
DTC P0562 FPCM
Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC P0562: System Voltage Low - FPCMDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
B+ | P0562 | P0562 | -- | -- |
Ground | -- | P0562 | -- | -- |
Circuit/System Description
The fuel pump control module (FPCM) monitors the battery voltage to ensure that the voltage stays within the proper range. Damage to components, and incorrect data may occur when the voltage is out of range.
Conditions for Running the DTC
The engine is running.
Conditions for Setting the DTC
The FPCM detects that the battery voltage is less than 9 V.
Action Taken When the DTC Sets
DTC P0562 is a type C DTC.
Conditions for Clearing the DTC
DTC P0562 is a type C DTC.
Schematic Reference
| • | Engine Controls Schematics for the 1.6L (LDE) and 1.8L (2HO) engines |
| • | Engine Controls Schematics for the 2.0L gasoline engines |
| • | Engine Controls Schematics for the 2.0L (LBS) diesel engine |
| • | Engine Controls Schematics for the 2.8L (LBW) engine |
Connector End View Reference
Description and Operation
Charging System Description and Operation
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing
- Engine running, accessories OFF, measure and record the battery voltage at the battery terminals. The voltage should be between 12.6 and 15.0 V.
- Ignition OFF, disconnect the harness connectors at the FPCM.
- Ignition OFF and scan tool disconnected, open and close the driver door, and wait 1 minute. Test for less than 5 Ω between the ground circuit terminal 1 and ground.
- Verify that a test lamp illuminates between the B+ circuit terminal 32 and ground.
- If all circuits test normal, replace the FPCM.
| ⇒ | If not within the specified range, refer to Charging System Test. |
| ⇒ | If greater than the specified range, test the ground circuit for an open/high resistance. |
| ⇒ | If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References - for FPCM replacement, setup, and programming.
