1. Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
2. Review Strategy Based Diagnosis for an overview of the diagnostic approach.
3. Diagnostic Procedure Instructions provides an overview of each diagnostic category.

The turbocharger pressure sensor responds to pressure changes in the intake manifold. The pressure changes occur based on the engine load, and turbocharger boost. The engine control module (ECM) supplies 5 V to the turbocharger pressure sensor on the 5-volt reference circuit. The ECM provides a ground on the low reference circuit. The turbocharger pressure sensor provides a signal to the ECM on the signal circuit which is relative to the pressure changes in the manifold.

P0234 00

The actual turbocharger boost pressure is greater than the desired range for greater than 6 s.

P0299 00

The actual turbocharger boost pressure is less than the desired range for greater than 6 s.

DTCs P0234 and P0299 are Type B DTCs.

DTCs P0234 and P0299 are Type B DTCs.

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Turbocharger System Description

Electrical Information Reference

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Special Tools

EN-23738-A Mityvac

For equivalent regional tools, refer to Special Tools.

1. Ignition ON, compare the scan tool Boost Pressure Sensor parameter to the BARO Sensor parameter. Both parameters should be within 5 kPa (0.72 PSI).

⇒	If not within the specified range, refer to Diagnostic Trouble Code (DTC) List - Vehicle for further diagnosis.

2. Observe the DTC information with a scan tool. Verify that DTC P0045, P0047, or P0048 are not set.

⇒	If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle for further diagnosis.

3. Engine running, increase the engine speed to 2 000 RPM. Command the Turbocharger Vane Position from ON and OFF with a scan tool. Verify the scan tool Boost Pressure Sensor parameter increases and decreases with the scan tool commands.
4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

1. Inspect the fuel tank for the right fuel content
2. Inspect the intake, and the exhaust systems, for the following:

•	Leaks or restrictions

•	Damaged or missing components

•	Aftermarket components

⇒	If a condition is found, repair as necessary.

3. Disconnect the vacuum source from the Q41 Turbocharger Vane Position Control Solenoid Valve
4. Connect the EN-23738-A Mityvac to the Q41 Turbocharger Vane Position Control Solenoid Valve vacuum supply hose. Engine running, verify the vacuum is greater than -50 kPa (-7.25 PSI).

⇒	If less than the specified range, inspect the vacuum supply hose and filter for a leak or restriction. If the supply hose is normal, replace the vacuum pump.

5. Connect the vacuum source to the Q41 Turbocharger Vane Position Control Solenoid Valve. Connect the EN-23738-A Mityvac to the Q41 Turbocharger Vane Position Control Solenoid Valve vacuum port on the Q41 Turbocharger Vane Position Control Solenoid Valve. Engine running, command the Turbocharger Vane Position OFF with a scan tool. Verify the vacuum is at 0 kPa (0 PSI).

⇒	If greater than the specified range, replace the Q41 Turbocharger Vane Position Control Solenoid Valve.

6. Command the Turbocharger Vane Position ON with a scan tool. Verify the vacuum is greater than -50 kPa (-7.25 PSI).

⇒	If less than the specified range, replace the Q41 Turbocharger Vane Position Control Solenoid Valve.

7. Inspect the turbocharger oil supply lines for a restriction.

⇒	If restricted, repair or replace as necessary.

8. If all other components test normal, replace the turbocharger.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.