Diagnostic Instructions

DTC Descriptors

DTC P0341: Intake Camshaft Position Sensor Performance Bank 1

DTC P0342: Intake Camshaft Position Sensor Circuit Low Voltage Bank 1

DTC P0343: Intake Camshaft Position Sensor Circuit High Voltage Bank 1

DTC P0346: Intake Camshaft Position Sensor Performance Bank 2

DTC P0347: Intake Camshaft Position Sensor Circuit Low Voltage Bank 2

DTC P0348: Intake Camshaft Position Sensor Circuit High Voltage Bank 2

DTC P0366: Exhaust Camshaft Position Sensor Performance Bank 1

DTC P0367: Exhaust Camshaft Position Sensor Circuit Low Voltage Bank 1

DTC P0368: Exhaust Camshaft Position Sensor Circuit High Voltage Bank 1

DTC P0391: Exhaust Camshaft Position Sensor Performance Bank  2

DTC P0392: Exhaust Camshaft Position Sensor Circuit Low Voltage Bank 2

DTC P0393: Exhaust Camshaft Position Sensor Circuit High Voltage Bank 2

Diagnostic Fault Information

Circuit	Short to Ground	Open/High Resistance	Short to Voltage	Signal Performance
CMP Sensor 5-Volt Reference	P0343, P0348, P0368, P0393, P0652, P2122, P2138	P0343, P0348, P0368, P0393, P0651	P0653, P2123, P2138	P0341, P0346, P0366, P0391, P0651, P0652, P0653, P2138
CMP Sensor Signal Intake Bank 1	P0342	P0343	P0343	P0341
CMP Sensor Signal Intake Bank 2	P0347	P0348	P0348	P0346
CMP Sensor Signal Exhaust Bank 1	P0367	P0368	P0368	P0366
CMP Sensor Signal Exhaust Bank 2	P0392	P0393	P0393	P0391
Low Reference	--	P0343, P0348, P0368, P0393	--	P0341, P0346, P0366, P0391

Circuit/System Description

Each camshaft is equipped with a camshaft position sensor that the engine control module (ECM) monitors. The CMP sensor is a hall effect switch that works in conjunction with a 4X reluctor wheel. The reluctor wheels are mounted to the camshaft position actuators that are mounted to the end of the camshafts. The ECM uses the CMP sensor signals in order to determine the position of the camshafts. The ECM supplies 5 volts to the CMP sensors on the 5 V reference circuits, and supplies a ground on the low reference circuits. The CMP sensors provide a signal to the ECM on the signal circuits. If the ECM detects extra or missing CMP sensor signal transitions, or a signal voltage that is more or less than the predetermined range, within a certain number of crankshaft revolutions, one of these DTCs sets.

Conditions for Running the DTC

Conditions for Setting the DTC

P0341, P0346, P0366, P0391

P0342, P0347, P0367, P0392

The CMP sensor signal voltage is always low and the ECM detects no pulses from the CMP sensor for greater than 1 second, or cumulative of 10 seconds.

P0343, P0348, P0368, P0393

The CMP sensor signal voltage is always high and the ECM detects no pulses from the CMP sensor for greater than 1 second or cumulative of 10 seconds.

Action Taken When the DTC Sets

DTCs P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, and P0393 are Type B DTCs.

Conditions for Clearing the DTC

DTCs P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, and P0393 are Type B DTCs.

Diagnostic Aids

The following conditions can also set the DTC:

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Electronic Ignition (EI) System Description

Electrical Information Reference

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

1. Ignition ON, observe the DTC information with a scan tool. DTC P0641, P0642, P0643, P0651, P0652, P0653, P0697, P0698 or P0699 should not be set.

⇒	If a DTC is set, refer to DTC P0641-P0643, P0651-P0653, or P0697-P0699.

2. Engine idling, observe the DTC information with a scan tool. DTC P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, or P0393 should not set.
3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, remove the fuse that supplies B+ to terminal 56 X2 of the ECM.
2. Disconnect the harness connector at the appropriate B23 camshaft position sensor.

Note: The control module or the sensor may be damaged if the circuit is shorted to B+ voltage.

3. Test for less than 5 Ω between the low reference circuit terminal 1 and ground.

⇒	If greater than the specified range, test the low reference circuit for an open/high resistance or for a short to voltage. If the circuit/connections test normal, replace the K20 ECM.

4. Install the fuse that supplies B+ to terminal 56 X2 of the ECM.
5. Ignition ON, test for greater than 4.8 V between the 5-volt reference circuit terminal 3 and ground.

⇒	If less than the specified value, test the 5-volt reference circuit for an open/high resistance. If the circuits/connections test normal, replace the K20 ECM.

6. Test for 4.8-5.2 V between the signal circuit terminal 2 and ground.

⇒	If the voltage is greater than specified range, test for a short to voltage in the signal circuit. If circuit/connections test normal, replace the K20 ECM.

⇒	If the voltage is less than the specified range, test for a short to ground or an open/high resistance in the signal circuit. If circuit/connections test normal, replace the K20 ECM.

7. If all circuits/connections test normal, replace the B23 camshaft position sensor.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.