Power Door Locks Inoperative Aztek
Test Description
The number below refers to the step number on the diagnostic table.
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Door Lock/Indicator Schematics Connector End View Reference: Power Door Systems Connector End Views , Computer/Integrating Systems Connector End Views in Computer/Integrating Systems, or Electrical Center Identification Views in Wiring Systems | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
2 | Verify the power door locks inoperative fault is present. Do the power door locks operate normally? | Go to Testing for Intermittent Conditions and Poor Connections in Wiring System | Go to Step 3 |
Are all of the power door locks inoperative, including the endgate locks? | Go to Step 4 | Go to Step 5 | |
4 |
Does the scan tool display change from Inactive to Active? | Go to Step 8 | Go to Step 7 |
5 | Test the appropriate door lock actuator unlock control circuit for a short to ground or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 13 | Go to Step 6 |
6 | Test the appropriate door lock actuator lock control circuit for a short to ground or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 13 | Go to Step 10 |
7 | Test the driver door lock switch lock signal circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 13 | Go to Step 8 |
8 | Inspect for poor connections at the center console fuse block harness connector C2. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 13 | Go to Step 9 |
9 | Inspect for poor connections at the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 13 | Go to Step 11 |
10 | Inspect for poor connections at the appropriate door lock actuator. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 13 | Go to Step 12 |
11 | Replace the BCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | Go to Step 13 | -- |
12 | Replace the appropriate door lock actuator. Refer to Front Side Door Lock Actuator Replacement or Rear Side Door Lock Actuator Replacement . Did you complete the repair? | Go to Step 13 | -- |
13 | Operate the system in order to verify the repair. Did you find and correct the condition? | System OK | Go to Step 3 |
Power Door Locks Inoperative Rendezvous
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Door Lock/Indicator Schematics Connector End View Reference: Power Door Systems Connector End Views , Computer/Integrating Systems Connector End Views in Computer/Integrating Systems, or Electrical Center Identification Views in Wiring Systems | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
2 | Verify the power door locks inoperative fault is present. Do the power door locks operate normally? | Go to Testing for Intermittent Conditions and Poor Connections in Wiring System | Go to Step 3 |
3 | Are all of the power door locks inoperative from both door lock switches? | Go to Step 6 | Go to Step 4 |
4 | Are the power door locks inoperative from a single door lock switch? | Go to Step 7 | Go to Step 5 |
5 | Is the driver door lock actuator the inoperative actuator? | Go to Step 8 | Go to Step 9 |
6 |
Do the door lock actuators activate? | Go to Step 10 | Go to Step 11 |
7 | Test the appropriate door lock switch ground circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 25 | Go to Step 12 |
8 | Test the driver door lock actuator unlock control circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 25 | Go to Step 13 |
9 | Test the appropriate door lock actuator unlock control circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 25 | Go to Step 13 |
10 | Test the driver door lock switch lock signal circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 25 | Go to Step 19 |
11 | Is the power door locks fuse open? | Go to Step 14 | Go to Step 15 |
12 | Test the driver door lock switch lock signal circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 25 | Go to Step 20 |
13 | Test the appropriate door lock actuator lock control circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 25 | Go to Step 21 |
14 |
Does the power door locks fuse open? | Go to Step 16 | Go to Step 17 |
15 | Test the body control module (BCM) ground circuit at the center console fuse block harness connector C2 for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 25 | Go to Step 18 |
16 | Test the door lock actuator unlock control, the driver door lock actuator unlock control, and the door lock actuator lock control circuits for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 25 | Go to Step 18 |
17 |
Does the power door locks fuse open after any of the door lock actuators is connected? | Go to Step 21 | Go to Step 18 |
18 | Inspect for poor connections at the center console fuse block harness connector C2. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 25 | Go to Step 19 |
19 | Inspect for poor connections at the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 25 | Go to Step 22 |
20 | Inspect for poor connections at the appropriate door lock switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 25 | Go to Step 23 |
21 | Inspect for poor connections at the appropriate door lock actuator. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 25 | Go to Step 24 |
22 | Replace the BCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | Go to Step 25 | -- |
23 | Replace the appropriate door lock switch. Refer to Front Side Door Lock Actuator Replacement or Rear Side Door Lock Actuator Replacement . Did you complete the repair? | Go to Step 25 | -- |
24 | Replace the appropriate door lock actuator. Refer to Front Side Door Lock Actuator Replacement or Rear Side Door Lock Actuator Replacement . Did you complete the repair? | Go to Step 25 | -- |
25 | Operate the system in order to verify the repair. Did you find and correct the condition? | System OK | Go to Step 2 |
