Tool Required

J 36850 Transmission Assembly Lubricant

1. Remove the case side cover. Refer to Control Valve Body Cover Replacement .
2. Remove the oil pump. Refer to Oil Pump Replacement .



3. Remove the valve body bolts (374-381, 384).



4. Remove the valve body (300) while keeping the spacer plate (396) with the transaxle.



5. Remove the ball check valves (372, 373) from the valve body.



6. Remove the spacer plate (370) and gasket.



7. Remove the ball check valves (372) from the case cover.



8. Inspect each check valve seat in the spacer plate (370) for excessive peening. Place a ball check valve (372) on each seat and use a flashlight in order to look for visible light between the valve and the seat.
9. Inspect all components removed from the transaxle. Refer to the Transmission/Transaxle/Transfer Case Unit Repair Manual.

Notice: Do NOT use any type of grease to retain parts during the assembly of this unit. Using greases other than the recommended assembly lube changes the transaxle fluid characteristics. Using greases other than the recommended assembly lube causes undesirable shift conditions and/or filter clogging. Use TRANSJEL™ J 36850 or equivalent during the assembly of this unit.

1. Install the ball check valves (372) into the case cover. Use the J 36850 to retain the ball check valves in their proper locations.



2. Install the gasket and the spacer plate (370).



3. Install the ball check valves (372, 373) into the valve body. Use the J 36850 to retain the ball check valves in their proper locations.



4. Install the screen/seal assemblies (382) into the spacer plate and gasket assembly (396).
5. Install the spacer plate and gasket assembly (396) onto the control valve body (300).
6. Install the bolts (368) to hold the spacer plate and gaskets onto the control valve body (300).



7. Install the control valve body alignment sleeve (410) into the case cover (400).

Important: 

•	Use the control valve body alignment sleeve (410) and turbine shaft sleeve in the case cover (400) as guides.

•	Be sure the ball check valves do not drop out of the control valve body (300) during assembly.

Important: Do NOT use impact type tools on the valve body or on the oil pump.

8. Install the gasket (371) and the valve body (300).

Notice: Refer to Fastener Notice in the Preface section.




9. Install the valve body bolts (374-381, 384).

Tighten

•	Tighten the M6 X 1.0 X 20 bolt to 8 N·m (70 lb in).

•	Tighten the M6 X 1.0 X 30 bolt to 12 N·m (106 lb in).

•	Tighten the M6 X 1.0 X 45 bolt to 12 N·m (106 lb in).

•	Tighten the M6 X 1.0 X 55 bolt to 12 N·m (106 lb in).

•	Tighten the M6 X 1.0 X 60 bolt to 12 N·m (106 lb in).

•	Tighten the M6 X 1.0 X 65 bolt to 12 N·m (106 lb in).

•	Tighten the M6 X 1.0 X 85 bolt to 12 N·m (106 lb in).

•	Tighten the M6 X 1.0 X 95 bolt to 16 N·m (12 lb ft).

•	Tighten the M8 X 1.25 X 90 bolt to 25 N·m (18 lb ft).

Important: Do NOT use impact type tools on the valve body or on the oil pump.

10. Install the oil pump. Refer to Oil Pump Replacement .
11. Install the case side cover. Refer to Control Valve Body Cover Replacement .

Important: It is recommended that transmission adaptive pressure (TAP) information be reset.

Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result, The ECM, PCM or TCM will need to relearn TAP values. Transmission performance may be affected as new TAP values are learned.
12. Reset the TAP values. Refer to Adapt Function.