Fuel Injection Fuel Rail Assembly Replacement VIN 1

Notice: 

•	Use care when servicing the fuel system components, especially the fuel injector electrical connectors, the fuel injector tips, and the injector O-rings. Plug the inlet and the outlet ports of the fuel rail in order to prevent contamination.

•	Do not use compressed air to clean the fuel rail assembly as this may damage the fuel rail components.

•	Do not immerse the fuel rail assembly in a solvent bath in order to prevent damage to the fuel rail assembly.

1. Bleed the fuel pressure from the fuel system. Refer to Fuel Pressure Relief .
2. Clean the fuel rail assembly and connections.
3. Remove the fuel feed and return pipes from the fuel rail tubes by squeezing tabs and pulling the lines apart.
4. Remove the vacuum line from the pressure regulator.
5. Remove the vacuum lines from the throttle body.
6. Remove the ignition coil wires from the coil and retainer clips on top of super charger.
7. Remove the generator and rear generator mounting bracket. Refer to Charging System.
8. Remove the injector electrical connectors
9. Remove the injector electrical harness clips holding harness to front of fuel rail.
10. Remove the fuel rail hold-down bolts.

Important: When servicing the fuel rail assembly, precautions must be taken to prevent dirt and other contaminants from entering the fuel passages. It is recommended that the fittings be capped, and the holes be plugged during servicing.

11. Remove the fuel rail with equal force on both sides of the fuel rail.

Caution: In order to reduce the risk of fire and personal injury that may result from a fuel leak, always install the fuel injector O-rings in the proper position. If the upper and lower O-rings are different colors (black and brown), be sure to install the black O-ring in the upper position and the brown O-ring in the lower position on the fuel injector. The O-rings are the same size but are made of different materials.

Notice: 

1. The O-rings must be replaced on all components that are replaced.
2. Lightly oil the fuel injector O-rings with clean motor oil.
3. Place the fuel rail assembly on the intake manifold.
4. Seat the fuel injectors by HAND.
5. Install the fuel rail hold-down bolts.

Tighten
Tighten the fuel rail hold-down bolts to 10 N·m (7 lb ft).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

6. Install the generator and rear generator mounting bracket. Refer to Charging System
7. Install the injector electrical harness clips holding harness to front of fuel rail.
8. Install the injector electrical connectors
9. Install the ignition coil wires to coil and retainer clips on top of super charger.
10. Install the vacuum line to the pressure regulator.
11. Install the vacuum lines to throttle.
12. Install the fuel feed and return pipes to the fuel rail tubes by squeezing tabs and pulling the lines apart.

Fuel Injection Fuel Rail Assembly Replacement VIN K

Important: When servicing the fuel rail assembly, precautions must be taken to prevent dirt and other contaminants from entering the fuel passages. It is recommended that the fittings be capped, and the holes be plugged during servicing.

1. Bleed the fuel pressure from the fuel system. Refer to Fuel Pressure Relief .
2. Clean the fuel rail assembly and connections.
3. Remove the fuel feed and return pipes from the fuel rail tubes by squeezing tabs and pulling the lines apart.
4. Remove the vacuum line from the pressure regulator.
5. Remove the vacuum line from the throttle body.
6. Remove the ignition coil wires.
7. Remove the injector electrical connectors.
8. Remove the fuel rail hold-down bolts.
9. Remove the fuel rail with equal force on both sides of the fuel rail.

Caution: In order to reduce the risk of fire and personal injury that may result from a fuel leak, always install the fuel injector O-rings in the proper position. If the upper and lower O-rings are different colors (black and brown), be sure to install the black O-ring in the upper position and the brown O-ring in the lower position on the fuel injector. The O-rings are the same size but are made of different materials.

Notice: 

1. The O-rings must be replaced on all components that are replaced.
2. Lightly oil the fuel injector O-rings with clean motor oil.
3. Place the fuel rail assembly on the intake manifold.
4. Seat the fuel injectors by HAND.
5. Install the fuel rail hold down bolts.

Tighten
Torque the fuel rail hold-down bolts to 10 N·m (7 lb ft).

6. Install the fuel injector electrical connectors.
7. Install the fuel feed and return pipes to the fuel rail tubes.
8. Install the vacuum to pressure regulator.
9. Install the vacuum line to throttle.
10. Install the ignition coil wires.